Abstract:Detailed heat transfer characteristics over high-pressure turbine endwall surfaces with coolant injection were experimentally studied in this paper. Heat transfer experiments were conducted in a properly scaled-up endwall model for an engine-representative oncoming flow profile with a high freestream turbulence intensity of 9.8% at an exit Reynolds number of 0.76 x 10(6) and an exit Mach number of 0.37. Cooling for the endwall was accomplished by upstream purge flow from a slot and film coolant from three axial rows of discrete film-cooling holes within the vane passage on the endwall. An engine-like coolant-to-mainstream density ratio of 1.70 was achieved by using cooled foreign gas. High-resolution measurements of the endwall heat transfer coefficients were conducted by using a steady, high-resolution infrared thermography technique based on the superposition principle for purge flow blowing ratios of 0.1-0.45 and film coolant injection blowing ratios of 1.4-3.6, respectively. In particular, the effects of the cooling geometries without blowing were considered to simulate hole blockage due to deposition. Results showed that local heat transfer coefficients near the film-cooling hole exits were significantly enhanced due to strong interactions between film coolant injection and mainstream flows, but those downstream of the slot were inhibited, somewhat, by purge flow, resulting from the suppression of purge flow on horseshoe vortex at the vane leading edge. The inhibiting effects of purge flow on the endwall heat transfer are more prominent when purge flow and the film coolant are injected simultaneously. For the discrete holes, higher coolant injection rates generate increased heat transfer levels. Because ingestion and re-injection of mainstream flows through the slot or the film-cooling holes without blowing, the presence of both cooling geometries causes heat transfer enhancement, and the enhancement by the film-cooling holes is higher than that by the slot. The detailed heat transfer measurements in this paper can provide useful thermal boundaries for an optimized endwall film-cooling design that will be investigated in a follow-up study.

TIME-RESOLVED HEAT TRANSFER MEASUREMENTS ON TURBINE OUTER ENDWALL IN A BLOWN-DOWN TRANSIENT TEST FACILITY

Comparison of Heat Transfer Measurement Techniques on a Transonic Turbine Blade Tip

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Infrared thermography with non-uniform heat flux boundary conditions on the rotor endwall of an axial turbine

Lessons Learned Toward Estimating the High-Pressure Turbine Inlet Temperature Profile Using Measurements Acquired at the High-Pressure Turbine Exit

Experimental Study on the Endwall Aerothermal Performance of Turbine Cascades in a Novel Transient Test Facility

Measurements of Heat Transfer and Pressure in a Trailing Edge Cavity of a Turbine Blade

Heat Transfer Measurements of a Turbine Endwall with Engine-Representative Freestream Turbulence and Inlet Swirl

The single-blow transient test technique using pulse change inlet condition with optimized pulse width and matching time

Reconstructing Turbine Non-Uniform Flow Including Hot Streaks Using Spatially Under-Sampled Measurements

Transient State Flow and Heat Transfer Performance over the Flat Tip of HP Turbine

Temperature field measurement of turbine rotor blade leading edge based on infrared radiation pyrometer

Experimental Evidence of Temperature Ratio Effect on Turbine Blade Tip Heat Transfer

Experimental Study of Turbine Blade Tip Heat Transfer with High-Speed Relative Casing Motion

Ramp Heating in High-Speed Transient Thermal Measurement with Reduced Uncertainty

Dynamic Measurement of Temperature Field and Deformation in Hydraulic Turbine Blade at Cooling Stage of Heat Treatment

Review: Radiation Temperature Measurement Methods for Engine Turbine Blades and Environment Influence

Measurement and Analyses of Heat Flux Data in a Turbine Stage: Part I—Description of Experimental Apparatus and Data Analysis

Measurements of Detailed Heat Transfer Characteristics on a High-Pressure Turbine Vane Endwall with Coolant Injection

High-temperature high-frequency turbine exit flow field measurements in a military engine with a cooled unsteady total pressure probe

Novel Strategy for Thermal Evaluation of Film-Cooled Blades Using Thermographic Phosphors at Simulated Engine Conditions