Abstract:Scandium is very expensive and limits the application potential of Sc containing alloys. A novel high-strength Al–Mg–Mn-Sc-Zr alloy was designed for reducing Sc. Multiple strengthening mechanisms were utilized for designing this alloy, especially for the solid solution strengthening which benefits from ultrahigh cooling. With the addition of Mn and Si, the strength of our alloy reaches comparable level of similar alloys while the Sc content is 40–60 % less than them. The effect of Mn addition on microstructure and mechanical properties were carefully studied. Near full-dense samples with relative density >99.88 % were obtained with the help of overlapping prediction model. The continuous Mg2Si network was observed with Si introduction and broken up with increasing Mn content. According to the tensile experiment results and corresponding calculations, it was considered that the thermal stability and the effect of precipitate strengthening was slightly deteriorated. However, obvious improvement of the tensile strength was observed with increasing Mn addition, and the ductility maintains in a certain range. After aging at 280 °C for 4 h, the sample of 1.4 wt% Mn exhibits the highest ultimate strength of 497.08 ± 7.22 MPa, and possesses a considerable ductility of 8.01 ± 0.34 %. The Portevin-Le Chatelier (PLC) effect was observed in stress-strain curves, which reflects a dynamic strain aging of mobile dislocations and solute atoms. After aging, the stress amplitude and waiting time of serration flow decrease obviously, because of the introduction of bypassing precipitates and reduction of diffusion time. Compared with other similar alloys, our alloy exhibited comparable yield strength and elongation, but considerable advantages in material costs resulting from lower Sc content. It will offer not only an idea for alloy design utilizing the ultra-high solid solubility of elements, but also a feasible way to further expand application field of high-strength Al-based alloys through reducing the material costs.

Sc3+–Lu3+‐Doped Α‐sialons

Sc3+-Lu3+-Doped Alpha-Sialons

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

High-temperature strength and oxidation behavior of Sc3+/Lu3+ co-doped α-sialon

Composition controlled microstructure and mechanical properties of Yb/Lu co-doped SiAlON

Microstructure and Properties of Self-Reinforced Α-Sialon Ceramics Doped with Lu2O3

Effect of Post Heat Treatment on Microstructure and Mechanical Properties of Lu-doped Α-Sialons

Sintering Behavior, Microstructure and Mechanical Properties of Various Fluorine-Containing Y-SiAlON Glass-Ceramics

Microstructure Characteristics And High-Temperature Performance Of In-Situ Reinforced Alpha-Sialon Ceramics

Influence of the interaction between Si and Sc on the microstructure and tensile properties of as casted Al-Si-Sc alloys

Microstructure and Mechanical Properties of Al–Si–Mg–Cu–Ti Alloy with Trace Amounts of Scandium

Modification Mechanism And Growth Process Of Al-3(Sc, Zr) Particles In As-Cast Al-Si-Mg-Cu-Zr-Sc Alloy

Effect of Si addition on the precipitation and mechanical/electrical properties of dilute Al-Zr-Sc alloys

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

The Effect of Mn Content on a Novel Al–Mg–Si-Sc-Zr Alloy Produced by Laser Powder Bed Fusion: the Microstructure and Mechanical Behavior

Microstructure and Mechanical Properties of Casting Al-3Li-2Mg-1Zn-0.1Zr Alloys Modified by Sc Additions

High Infrared Transmission of Y3+–Yb3+-doped Α-Sialon

Effect of Sc Microalloying Addition on Microstructure and Mechanical Properties of As-Cast Al–12Si Alloy

On the Sc induced solidification-heterogeneous microstructure in selective laser melted Al-5Mn alloys

In Situ Toughened Α-Sialon Ceramics Doped with Lutecia and Ytterbia