Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Multistage Wavefront Control for a Segmented Primary Mirror with Annular-Sector Subaperture

Decoupling Control for Position Error and Surface Error of Segmented Primary Mirror

Modified Wavefront Sensing and Correction Methodology for Active Segment Mirror of Large Space Telescope

Phase Alignment Of Segmented Mirrors Using A Digital Wavefront Interferometer

Wavefront Alignment Research of Segmented Mirror Synthetic Aperture Optical (sao) System

Wavefront Compensation Segmented Mirror Sensing and Control

Active Control for Segmented Deployable Ultra-thin Piezoelectric Space Telescope.

Location-grouping Algorithm Based on Limited Actuators Deformable Mirror for High Precision Wavefront Aberration Correction in Adaptive Optics System

Active Optics and Aberration Correction Technology for Sparse Aperture Segmented Mirrors

Design and analysis of segmented-mirror primary mirror system

Wavefront Error Modeling and Control Method for Large Aperture Optical Unit in High Power Solid-State Laser

Low Spatio-temporal Frequency Wavefront Aberration Correction Method Based on a Movable Secondary Mirror

Effect of Radius Mismatch on Performance of Segmented Telescopic Systems

Keck Primary Mirror Closed-loop Segment Control Using a Vector-Zernike Wavefront Sensor

Segmented mirror fine phasing using model-based wavefront sensorless adaptive optics and Chebyshev segmented piston-tip-tilt modes

Large Range of a High-Precision, Independent, Sub-Mirror Three-Dimensional Co-Phase Error Sensing and Correction Method via a Mask and Population Algorithm

Co-phase quantization and adjustment of segmented mirrors based on dual-wavelength vortex interference

Wavefront Control in Adaptive Microscopy Using Shack-Hartmann Sensors with Arbitrarily Shaped Pupils.

Correcting Errors in Definite Area: a New Method for Controlling Mid-Spatial-frequency Errors in Optical Surface

Analysis on Curvature Radius Error of Segmented Primary Mirror