Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Decoupling Control for Position Error and Surface Error of Segmented Primary Mirror

Novel Electro-Hydraulic Position Control System for Primary Mirror Supporting System

Wavefront Compensation Segmented Mirror Sensing and Control

Modified Wavefront Sensing and Correction Methodology for Active Segment Mirror of Large Space Telescope

Large Range of a High-Precision, Independent, Sub-Mirror Three-Dimensional Co-Phase Error Sensing and Correction Method via a Mask and Population Algorithm

Design and analysis of segmented-mirror primary mirror system

Experiments on Quasi-Static and Dynamic Control of a PVDF Laminated Membrane-Like Mirror

Mode-Voltage Constrained Control for Adaptive Optics System

Learning Approach for Flexible Spherical/Aspherical Reflective Surface Control

Research on Active Control for Thermal Deformation of Precise Membrane Reflector With Boundary SMA Actuators

Quantitative feedback controller design and test for an electro-hydraulic position control system in a large-scale reflecting telescope

Co-phase quantization and adjustment of segmented mirrors based on dual-wavelength vortex interference

Air Flow Turbulence Orthogonality and Surface Error Estimation in Large Aperture Optical Testing

Freeform surface compensation design for machining error of primary mirror

Keck Primary Mirror Closed-loop Segment Control Using a Vector-Zernike Wavefront Sensor

Location-grouping Algorithm Based on Limited Actuators Deformable Mirror for High Precision Wavefront Aberration Correction in Adaptive Optics System

Post Optical Freeform Compensation Technique for Machining Errors of Large-Aperture Primary Mirror

Error-separation Model for Interferometric Testing Aspheric Surfaces Based on Wavefront Aberrations

Structure and Closed-Loop Control of A Novel Compact Deformable Mirror for Wavefront Correction in A High Power Laser System

Mirror actively deformed and regulated for applications in space: design and performance