Abstract:Ti6Al4V (TC4) alloy has been widely applied in the military, industrial, chemical, and medical fields due to their excellent thermal stability, corrosion resistance , and biocompatibility. However, titanium alloys are notorious for their poor tribological properties, such as their high friction coefficients and low surface bearing capacities. To tackle this problem, combination of laser surface texturing (LST) and double glow plasma chromizing was conducted to improve the wear resistance of TC4. LST was first conducted to produce uniform dimples with a diameter of 300 μm and gradient density of 11 % on the Ti6Al4V substrate. A chromizing coating (Cr-coating) was subsequently deposited on the surfaces of the textured and raw Ti6Al4V alloy by double glow plasma surface alloying (DGPSA). A continuous and compact Cr-coating with a thickness of about 55 μm was formed on TC4 after being maintained at a temperature of 850 °C, and the coating was mainly composed of a solid solution and intermetallic compounds of Cr 2 Ti phases. The surface hardness after alloying was two times higher than that of the TC4 substrate. Comparative assessments on the wear resistance of the Cr-coatings with and without LST treatment and the TC4 alloy were carried out using a ball-on-disk wear tester. The results showed that the mass loss and specific wear rate of the duplex-treated sample were 1.54 mg and 7.14 × 10 −4 mm 3 ·N −1 ·m −1 . The mass loss and specific wear rate of the TC4 were 4.32 mg and 1.62 × 10 −3 mm 3 ·N −1 ·m −1 . The specific wear rates of the four tested samples were in the following order: the duplex-treated TC4 < textured TC4 < chromized TC4 < polished TC4. The coating obtained by LST-double glow plasma chromizing duplex treatment exhibited an outstanding durability and the best mechanical performance. Thus, this approach be used for the protection of Ti6Al4V surface in engineering components and medical instruments.

Wear Resistance of Die Casting Die of Cover Lid of Engine by Laser Treatment

Anti-Wear Property of Laser Textured 42CrMo Steel Surface

Effect of Cr on Wear Resistance and Mechanism of Preset-Powder Laser Cladding T15 Alloy Steel Coating

Experimental Study on the Wear Properties of 42CrMo Steel with Different Microstructures and T15 Laser Cladding

Cover Die Service Life Improvement by Biomimetic Laser-Remelting Process and CAE Simulation

Microstructure and Soil Wear Resistance of a Grey Cast Iron Alloy Reinforced with Ni and Cr Laser Coatings

Bionic Laser Surface Remelting for the Wear Performance after Thermal Fatigue of B2 Die Steel Based on Surface Stress Simulation

Performance Enhancements of High-Pressure Die-Casting Die Processed by Biomimetic Laser-Remelting Process

Effect of laser shock peening on the retention ability of surface roughness in forged Cr5 steel

Superior wear resistance in cast aluminum alloy via femtosecond laser induced periodic surface structures and surface hardening layer

Researches of Cast Iron Piston Rings Strengthened by Laser

Combining laser surface texturing and double glow plasma surface chromizing to improve tribological performance of Ti6Al4V alloy

Effect of Triangular Texture on the Tribological Performance of Die Steel with Tin Coatings under Lubricated Sliding Condition

Effect of the Laser Cladding Parameters on Microstructure and Elevated Temperature Wear of FeCrNiTiZr Coatings

Wear Performance of Cast Iron Piston Rings Strengthened by Laser

Dry Wear Behaviors of Wear Resistant Composite Coatings Produced by Laser Cladding

Wear Resistance of Machine Tools' Bionic Linear Rolling Guides by Laser Cladding

Effect of laser rust removal on surface roughness of 3Cr2Mo die steel

Aluminum Chromium Nitride Coating on a Laser Shock Micro-Molded Surface of E690 High-Strength Steel and Its Antifriction Mechanism

Experimental and Numerical Study on Friction and Wear Performance of Hot Extrusion Die Materials

Analysis and Respond Surface Methodology Modeling on Property and Performance of Two-Dimensional Gradient Material Laser Cladding on Die-cutting Tool