Abstract:Hydrogels are a cross-linked network of polymers swollen with liquid and have the potential to be used as a synthetic replacement for local defects in load bearing tissues such as articular cartilage. Hydrogels display viscoelastic time dependent behavior, therefore experimental analysis of stresses at the surface and within the gel is difficult to perform. A three-dimensional model of a hydrogel was developed in the commercial finite element software ABAQUS™, implementing a poro-viscoelastic constitutive model along with a contact-dependent flow state and friction conditions. Water content measurements, sliding, and indentation experiments were performed on neat polyvinyl alcohol (PVA), and on low friction boundary lubricant functionalized (BLF-PVA) hydrogels, both manufactured by freeze-thaw processes. Modulus results from the indentation experiments and coefficient of friction values from the sliding experiments were used as material property inputs to the model, while water content was used to calculate initial flow conditions. Tangential force and normal displacement data from a three-dimensional simulation of sliding were compared with the experiments. The tangential force patterns indicated important similarities with the fabricated hydrogels that included an initially high force value due to time dependent deformation followed by a decrease in a stabile value. A similar trend was observed with the normal displacement. These comparisons rendered the model suitable as a representation and were used to analyze the development and propagation of stresses in the immediate surface region. The results showed that in a three-dimensional stress field during sliding, the maximum stress shifted to the surface and rotated closer to the leading edge of contact. This occurred because the stress field becomes dominated by an amplified compressive stress at the leading edge due to the biphasic viscoelastic response of the material during sliding. Also, the complex multi-axial contact stress field was reduced to focus predominately on stress in the contact surface region in the direction of sliding. The results showed that during biphasic viscoelastic frictional sliding, the maximum tensile stress develops at the trailing edge of contact and a compressive stress develops at the leading edge in the direction of motion. The BLF-PVA hydrogels displayed a decrease in this tensile and compressive stress as compared to the standard PVA. The diminishment of these stresses would be expected to give the BLF-PVA hydrogels lower material wear with greater life expectancy as a synthetic articular cartilage implant.

Effect of interaction between gel and substrate on the frictional behavior of poly (vinyl alcohol) hydro-gel

Effect Of Hyaluronan Solution On Dynamic Friction Of Pva Gel Sliding On Weakly Adhesive Glass Substrate

Substrate Effect on the Formation of Hydrogels with Heterogeneous Network Structure

Friction Of Soft Gel In Dilute Polymer Solution

Influence of Preparation Parameters on the Frictional Behavior of PVA Hydrogel Against Glass Substrate

Frictional Behavior of Poly(2-Acrylamido-2-Methylpropanesulfonic Acid) Hydrogel-Glass System-Influence of Compressive Modulus

Negative Velocity Dependence of Friction for Poly( 2-Acrylamido-2-methyl Propanesulfonic Acid) Hydrogel Sliding Against A Glass Surface in the Low- Velocity Region

Load-Dependent Behavior and Underneath Mechanism of Hydrogel Friction

Probing the intriguing frictional behavior of hydrogels during alternative sliding velocity cycles

Friction of poroelastic contacts with thin hydrogel films

Effect of contact geometry on the friction of acrylamide hydrogels with different surface structures

Wear Evaluation of Poly(vinyl alcohol) Hydrogel by UV Spectrometry and Total Organic Carbon Measurement of Lubricant

Adhesive and normal stress-dependent dynamic friction of a gelatin hydrogel

The Effects of Surface Mechanical Deformation and Bovine Serum Albumin on the Tribological Properties of Polyvinyl Alcohol Hydrogel as an Artificial Cartilage

Friction through molecular adsorption at the sliding interface of hydrogels: Theory and experiments

Tuning Lubrication Performance of Phase‐changing Emulsion‐filled Gels by Sugar alcohols

Tribological and Rheological Properties of Poly(vinyl alcohol)-Gellan Gum Composite Hydrogels

A study on the friction properties of PAAc hydrogel under low loads in air and water

Experimental and numerical tribological studies of a boundary lubricant functionalized poro-viscoelastic PVA hydrogel in normal contact and sliding

Molecular adsorption induces normal stresses at frictional interfaces of hydrogels

Studies on the Lubrication Between Hydrophilic-Hydrophilic/Hydrophobic-Hydrophobic Gemini Interfaces and Complex Fluids