Abstract:We report on the frictional behaviour of thin poly(dimethylacrylamide) (PDMA) hydrogels films grafted on glass substrates in sliding contact with a glass spherical probe. Friction experiments are carried out at various velocities and applied normal loads with the contact fully immersed in water. In addition to friction force measurements, a novel optical set-up is designed to image the shape of the contact under steady-state sliding. The velocity-dependence of both friction force $F_t$ and contact shape is found to be controlled by a Péclet number Pe defined as the ratio of the time $\tau$ needed to drain the water out of the contact region to a contact time $a/v$, where $v$ is the sliding velocity and $a$ is the contact radius. When Pe<1, the equilibrium circular contact achieved under static normal indentation remains unchanged during sliding. Conversely, for Pe>1, a decrease in the contact area is observed together with the development of a contact asymmetry when the sliding velocity is increased. A maximum in $F_t$ is also observed at Pe~$\approx$~1. These experimental observations are discussed in the light of a poroelastic contact model based on a thin film approximation. This model indicates that the observed changes in contact geometry are due to the development of a pore pressure imbalance when Pe>1. An order of magnitude estimate of the friction force and its dependence on normal load and velocity is also provided under the assumption that most of the frictional energy is dissipated by poroelastic flow at the leading and trailing edges of the sliding contact.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to understand the frictional behavior between thin poly(dimethylacrylamide) (PDMA) hydrogel films and glass spherical probes in an aqueous environment. Specifically, the research aims to explore the following aspects: 1. **Dependence of frictional force and contact shape**: Study how the frictional force $ F_t $ and contact shape change with the sliding velocity $ v $ and the applied normal load $ F_n $. 2. **Influence of Péclet number**: Introduce the Péclet number $ \text{Pe} = \frac{\tau v}{a} $, where $ \tau $ is the drainage time, $ v $ is the sliding velocity, and $ a $ is the contact radius. Use the Péclet number to describe the changes in frictional force and contact shape. 3. **Mechanism of contact geometry change**: Explain the reasons for the reduction in contact area and the formation of contact asymmetry when the Péclet number is greater than 1, especially the influence of pore - pressure imbalance on these phenomena. ### Summary of main problems - **Contact behavior at low - speed sliding**: When $ \text{Pe} < 1 $, the contact area remains circular, and the contact radius and frictional force are similar to those in static conditions. - **Contact behavior at high - speed sliding**: When $ \text{Pe} > 1 $, the contact area decreases, contact asymmetry appears, and the frictional force reaches its maximum value. - **Poroelastic effect**: Use the poroelastic model to explain the reasons for the change in contact geometry during high - speed sliding, especially the lift effect due to pore - pressure imbalance. ### Formula explanations - **Péclet number**: \[ \text{Pe} = \frac{\tau v}{a} \] where $ \tau $ is the drainage time, $ v $ is the sliding velocity, and $ a $ is the contact radius. - **Pore - pressure field**: \[ p(r, \theta)=-\frac{v}{8R e_0 \kappa} r^3 \cos \theta+\sum_{n = 0}^{\infty} \alpha_n r^n \cos(n \theta) \] - **Contact stress**: \[ \sigma(r, \theta)=\frac{\tilde{E}}{2R e_0}(a^2 - r^2)+p(r, \theta) \] - **Critical velocity**: \[ v_c=\frac{4\tilde{E} \kappa}{a_0} \] Through these formulas and experimental results, the author shows the important influence of the poroelastic effect on frictional behavior under high - speed sliding conditions and proposes a theoretical model to explain the observed phenomena.

Friction of poroelastic contacts with thin hydrogel films

Effect Of Hyaluronan Solution On Dynamic Friction Of Pva Gel Sliding On Weakly Adhesive Glass Substrate

Transient sliding of thin hydrogel films: the role of poroelasticity

Friction through molecular adsorption at the sliding interface of hydrogels: Theory and experiments

Poroelastic indentation of mechanically confined hydrogel layers

Precise Correlation of Contact Area and Forces in the Unstable Friction between a Rough Fluoroelastomer Surface and Borosilicate Glass

Frictional Behavior of Poly(2-Acrylamido-2-Methylpropanesulfonic Acid) Hydrogel-Glass System-Influence of Compressive Modulus

Negative Velocity Dependence of Friction for Poly( 2-Acrylamido-2-methyl Propanesulfonic Acid) Hydrogel Sliding Against A Glass Surface in the Low- Velocity Region

Mechanical response of a thick poroelastic gel in contactless colloidal-probe rheology

Friction Of Soft Gel In Dilute Polymer Solution

Friction of Polymers: from PDMS Melts to PDMS Elastomers

Molecular adsorption induces normal stresses at frictional interfaces of hydrogels

Probing the intriguing frictional behavior of hydrogels during alternative sliding velocity cycles

Friction as a probe of surface properties of a polymer glass

Probing the micromechanics of a multi-contact interface at the onset of frictional sliding

Effect of contact geometry on the friction of acrylamide hydrogels with different surface structures

Linking Friction and Surface Properties of Hydrogels Molded Against Materials of Different Surface Energies

Stress field at a sliding frictional contact: Experiments and calculations

Molecular Dynamics Simulations on the Frictional Behavior of a Perfluoropolyether Film Sandwiched Between Diamond-Like-carbon Coatings.

Influence of Preparation Parameters on the Frictional Behavior of PVA Hydrogel Against Glass Substrate

Probing locally the onset of slippage at a model multi-contact interface