Abstract:Three‐level hybrid surgery (HS) consisting of cervical disc arthroplasty (CDA) and anterior cervical discectomy and fusion (ACDF) has been partly used for the treatment of multi‐level cervical degenerative disc disease (CDDD). According to the different numbers and locations of CDAs and ACDFs, three‐level HS has several constructs. Few studies have concerned the von Mises stress on the prostheses, and no study had explored the von Mises stress on the vertebrae. However, the complications related to the implants and the collapsibility of the surgical vertebral bodies had been reported in multi‐level anterior cervical spine surgery. Thus, it is necessary to explore the biomechanical effects on the prostheses and vertebrae in three‐level HS. As a result, we found the stress on CDA prostheses in CDA‐ACDF‐CDA construct and the stress on ACDF prostheses in CDA‐ACDF‐CDA and ACDF‐CDA‐ACDF constructs were significantly increased. But the stress on vertebrae were lower compared with that in three‐level ACDF. Purpose Three‐level hybrid surgery (HS) consisting of cervical disc arthroplasty (CDA) and anterior cervical discectomy and fusion (ACDF) has been partly used for the treatment of multi‐level cervical degenerative disc disease (CDDD). The complications related to the implants and the collapse of the surgical vertebral bodies had been reported in multi‐level anterior cervical spine surgery. Thus, this study aimed to explore the biomechanical effects on the prostheses and vertebrae in three‐level HS. Methods A FE model of cervical spine (C0‐T1) was constructed. Five surgical models were developed. They were FAF model (ACDF‐CDA‐ACDF), AFA model (CDA‐ACDF‐CDA), FFF model (three‐level ACDF), SF model (single‐level ACDF), and SA model (single‐level CDA). A 75‐N follower load and 1.0‐N·m moment was applied to produce flexion, extension, lateral bending, and axial rotation. Results Compared with the intact model, the range of motion (ROM) of total cervical spine in FAF model decreased by 34.54%, 54.48%, 31.76%, and 27.14%, respectively, in flexion, extension, lateral bending, and axial rotation, which were lower than those in FFF model and higher than those in AFA model. The ROMs of CDA segments in FAF and AFA models were similar to the intact model and SA model. Compared with the intact model, the ROMs at C3/4 segment in FFF model increased from 5.71% to 7.85%, and increased from 5.31% to 6.81% at C7/T1 segment, following by FAF model, then the FAF model. The maximum interface pressures of the Prestige‐LP in FAF model were similar to SA model, however the corresponding values were increased in AFA model. The maximum interface pressures of the Zero‐P were increased in FAF and AFA model compared with those in SF and FFF models. The stress was mainly distributed on the screws. In AFA model, the maximum pressures of the ball and trough articulation in superior and inferior Prestige‐LP were all increased compared with those in SA and FAF model. In FFF model, the maximum pressures of the vertebrae were higher than those in other models. The stress was mainly distributed on the anterior area of the vertebral bodies. Conclusions HS seemed to be more suitable than ACDF for the surgical treatment of three‐level CDDD in consideration of the biomechanical effects, especially for the two‐level CDA and one‐level ACDF construct. But a more appropriate CDA prosthesis should be explored in the future.

Biomechanical Effects of Intersegmental Stability Due to Multilevel Cervical Laminectomy

Finite element analysis into the effect of discectomy on lumbar biomechanical characteristics

Finite Element Model Analysis of Lumbar Biomechanical Characteristics after Nucleus Discectomy

Biomechanical Comparison of Laminectomy, Hemilaminectomy and A New Minimally Invasive Approach in the Surgical Treatment of Multilevel Cervical Intradural Tumour: A Finite Element Analysis

Stress Analysis of Facets after Cervical Laminectomy

Stability of the whole lumbar spine after multilevel fenestration and discectomy

The Biomechanical Response of the Lower Cervical Spine Post Laminectomy: Geometrically-Parametric Patient-Specific Finite Element Analyses

Biomechanical Effect of Posterior Ligament Repair in Lamina Repair Surgery.

Biomechanical Effects on the Prostheses and Vertebrae of Three‐Level Hybrid Surgery: A Finite Element Study

Quantitatively Biomechanical Response Analysis of Posterior Musculature Reconstruction in Cervical Single-Door Laminoplasty.

Biomechanical Effects of Anterior Decompression and Fusion With Cervical Two-Segments Different Internal Fixation Systems: A Finite Element Study

Biomechanical Comparison of Different Surgical Strategies for Skip-level Cervical Degenerative Disc Disease: A Finite Element Study

Cadaveric biomechanical analysis of multilevel lateral lumbar interbody fusion with and without supplemental instrumentation

Biomechanical Effects of Different Lateral Mass Injury Patterns on Subaxial Cervical Fracture Dislocations after Anterior Cervical Surgery: a Finite Element Study.

[The Biomechanics Influence of Unilateral Laminectomy and Discectomy Surgery on the Adjacent Different Grades of Disc Degeneration].

Adjacent segment biomechanical changes after one- or two-level anterior cervical discectomy and fusion using either a zero-profile device or cage plus plate: A finite element analysis

Biomechanics influence in ossification of the posterior longitudinal ligament:a finite element model of cervical spine

Biomechanical response of decompression alone in lower grade lumbar degenerative spondylolisthesis--A finite element analysis

Three-dimensional finite element modeling of whole lumbar spine and its biomechanical analysis

Biomechanical evaluation of adjacent segment degeneration after one- or two-level anterior cervical discectomy and fusion versus cervical disc arthroplasty: A finite element analysis

Using Finite Element Models to Assess Spinal Cord Biomechanics after Cervical Laminoplasty for Degenerative Cervical Myelopathy