Abstract:In this paper, initiation and growth behavior tests of small fatigue crack in laboratory air and aqueous 3.5% NaCl were conducted using non-corroded and pre-corroded SENT specimens for 2024-T62 Aluminum alloy. In order to compare with the corresponding small cracks, large crack growth tests for non-corroded and corroded specimens with different prior corrosion times were performed. Variation of pre-corrosive pit sizes with corrosion time was also studied. The results show that for fatigue specimens with pre-corrosive pits, small cracks initiated from the corrosion pits in both laboratory air and aqueous 3.5% NaCl, and initiation lives of small cracks (a≤60μm) are below 25% of total fatigue lives. For non-corroded fatigue specimens in laboratory air, small cracks initiated naturally from voids of the material, and initiation lives of small cracks (a≤25μm) are below 20% of total fatigue lives. An obvious small crack effect was found at R=-1 for non-corroded material in laboratory air. However, the same effect was not found at R=0.06 for the non-corroded material in laboratory air, and for the corroded material in both laboratory air and aqueous 3.5% NaCl at R=-1 and 0.06. And effect of environment on growth of small cracks that initiated from pre-corrosive pits was not found for Al2024-T62. The similar tendency was also found in large crack growth tests. Moreover, effect of prior corrosion time on large crack growth rates was not found to be in existence for this material. By assuming a pre-corrosive pit as an initiating surface crack, the commercial software FASTRANII and AFGROW were used to predict fatigue lives of corroded specimens with different prior corrosions. The predictions were found to agree reasonably with the tests.

Anomalous growth behavior of fatigue crack for the forged 7B04 aluminum alloy

Small Crack Growth Behavior And Life Prediction Of 7075-T73 Forged Aluminum Alloy

Damage Mechanisms and Anisotropy of an AA7010-T7452 Open-Die Forged Alloy: Fatigue Crack Propagation

Corrosion fatigue crack propagation of 7XXX series aluminum alloys from key components of high-speed train

Small fatigue crack behavior and life prediction of pre-corroded 2024-T62 aluminum alloy

Fatigue Crack Propagation Behavior of the 2195-T8 Aluminum-Lithium Alloy with a Precorroded Hole

Anisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy

Quantitative Anisotropic Damage Mechanism in a Forged Aluminum Alloy Studied by Synchrotron Tomography and Finite Element Simulations

Corrosion fatigue crack propagation behavior of A7N01P‐T4 aluminum alloy welded joints from high‐speed train underframe after 1.8 million km operation

An In Situ Study of Short Crack Initiation and Propagation During Fatigue Testing of a Hot Isostatically Pressed Al-7%Si-0.5%Mg (A357-T6) Alloy Specimen

Investigation on fatigue crack propagation behaviors in the thickness direction of 2519A aluminum alloy thick plate

Short Surface Crack Growth of High-Strength Aluminum Alloy in Corrosion Fatigue.

Crack Growth Patterns of Aluminum Tubular Specimens Subjected to Cyclic Tensile Loads

Effect of Fatigue and Precorrosion Fatigue on Fatigue Crack Propagation and Fracture Failure Behavior of 5B70 Aluminum Alloy

Overload-induced anisotropy of fatigue crack growth in laser deposited Ti-6Al-4V alloy

Fatigue crack growth behavior of 2624-T39 aluminum alloy with different grain sizes

Explore the mechanism of high fatigue crack propagation rate in fine microstructure of friction stir welded aluminum alloy

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Corrosion Fatigue Behavior of Fastening Hole Structure and Virtual Crack Propagation Tests

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

Fatigue crack nucleation and microstructurally small crack growth mechanisms in high strength aluminum alloys