Abstract:The present work systematically investigates the effect of cavitator mounting strut and cavitator shape on the ventilation demand to form and sustain a ventilated supercavity under different flow conditions. Three cavitators of different shapes (i.e. 2D cavitators including triangle and disk shape, and 3D cone-shaped cavitator) with the same frontal area are employed for the experiments. The cavitator is connected to a ventilation pipe extended upstream from a mounting strut, referred to as forward-facing model (FFM). The minimal ventilation coefficients to generate (<math>CQf</math>) and to collapse (<math>CQc</math>) a supercavity are measured over a wide range of Froude number (<math>Fr</math>) for each cavitator. Images of overall cavity shapes and topology near closure region as well as the cavity pressure under different experimental conditions are captured simultaneously. The results are compared across different cavitator shapes and the disk cavitator situated on the downstream side of the mount strut, referred to as backward-facing model (BFM). Similar <math>CQf-Fr</math> curves were observed in BFM and FFM-configured disk cavitators. The cone-shaped cavitator requires the least amount of ventilation to generate a supercavity among all different shapes across the range of <math>Fr</math> in our experiments. The <math>CQc</math>of disk FFM is lower than that of its BFM counterpart at small <math>Fr</math> and exceeds the BFM <math>CQc</math>with further increase of <math>Fr</math>. The cone cavitator has the smallest <math>CQc</math> among all the cavitators across the range of <math>Fr</math> in our experiments. To elucidate the trends of <math>CQc</math> upon changing <math>Fr</math> and cavitator shape, the geometry of supercavity under <math>CQc</math> including its overall shape, the cavity maximum diameter (<math>Dmax</math>) and half length (<math>L1/2</math>) are also investigated. Both <math>Dmax</math> and <math>L1/2</math> show an increasing then plateauing trend upon increasing <math>Fr</math> across different FFM cavitators despite the smaller values for the 3D cone cavitator. Subsequently, such cavity geometric information and cavity pressure measurements in conjunction with high speed imaging of re-entrant jet are employed to estimate the re-entrant jet momentum under different <math>Fr</math> for disk and cone cavitators. The estimated re-entrant jet momentum shows reasonable match with the ventilation air momentum under <math>CQc</math> in lower <math>Fr</math> for both cavitator cases, with the disk cavitator case yielding significantly stronger re-entrant jet, providing support to the re-entrant jet mechanism governing on the cavity collapse. Our study sheds some light on the cavitator design and ventilation strategy for a supercavitating vehicle in practice.

Effect of cavitator diameter on the aft section hydrodynamic character of supercavitating vehicles

Study on Effects of the Shape of Cavitator on Supercavitation Flow Field Characteristics

EXPERIMENTAL RESEARCH ON HYDRODYNAMIC CHARACTER OF AFT SECTION OF UNDERWATER SUPERCAVITATING BODIES

Experimental Study on Supercavitation Characteristics around Axisymmetric Body with Different Shape Cavitators

Blockage Effect of a Wall on the Hydrodynamic Characteristics of a Supercavitating Vehicle's Aft Body

Cavity and hydrodynamic features of supercavitatingvehicle with conical cavitator

Numerical Simulation on Supercavity Characteristics of Disc Cavitator Based on SST Turbulence Model

Experimental Study on Morphological Characteristics of Ventilated Supercavity of Double Disc Cavitator Projectile

Effect of Attack Angle Change on Hydrodynamic Character of Supercavitating Bodies

EXPERIMENTAL RESEARCH ON SHAPE AND DRAG CHARACTERISTICS OF VENTILATED SUPERCAVITY ON UNDERWATER BODIES

The effect of ventilation on supercavity around a supercavitating vehicle during water-entry

EXPERIMENTAL INVESTIGATION OF CAVITATOR PARAMETERS EFFECTING ON VENTILATED SUPERCAVITY SHAPE

Experimental Study of the Drag Reduction of Ventilated Supercavity of Underwater Bodies

Exploring Experimentally Effect of Gas Entrainment Rate on Geometrical Shape of Supercavity

Study on cavitating flows around an axisymmetric body with cavitators

Hydrodynamic Characteristics and Supercavity Shape of Supercavitating Projectiles Launched with Supersonic Speed

INFLUENCE OF CAVITATOR PARAMETERS ON FORMATION AND DEVELOPMENT OF SUPERCAVITY

Effect of mounting strut and cavitator shape on the ventilation demand for ventilated supercavitation

Experimental Investigation on the Principle of Inception of Ventilated Supercavitation

Experimental Study on the Ventilation Rate of Artificial Supercavitation

Experimental and Numerical Study on the Oblique Water-Entry Impact of a Cavitating Vehicle with a Disk Cavitator