Abstract:The present work systematically investigates the effect of cavitator mounting strut and cavitator shape on the ventilation demand to form and sustain a ventilated supercavity under different flow conditions. Three cavitators of different shapes (i.e. 2D cavitators including triangle and disk shape, and 3D cone-shaped cavitator) with the same frontal area are employed for the experiments. The cavitator is connected to a ventilation pipe extended upstream from a mounting strut, referred to as forward-facing model (FFM). The minimal ventilation coefficients to generate (<math>CQf</math>) and to collapse (<math>CQc</math>) a supercavity are measured over a wide range of Froude number (<math>Fr</math>) for each cavitator. Images of overall cavity shapes and topology near closure region as well as the cavity pressure under different experimental conditions are captured simultaneously. The results are compared across different cavitator shapes and the disk cavitator situated on the downstream side of the mount strut, referred to as backward-facing model (BFM). Similar <math>CQf-Fr</math> curves were observed in BFM and FFM-configured disk cavitators. The cone-shaped cavitator requires the least amount of ventilation to generate a supercavity among all different shapes across the range of <math>Fr</math> in our experiments. The <math>CQc</math>of disk FFM is lower than that of its BFM counterpart at small <math>Fr</math> and exceeds the BFM <math>CQc</math>with further increase of <math>Fr</math>. The cone cavitator has the smallest <math>CQc</math> among all the cavitators across the range of <math>Fr</math> in our experiments. To elucidate the trends of <math>CQc</math> upon changing <math>Fr</math> and cavitator shape, the geometry of supercavity under <math>CQc</math> including its overall shape, the cavity maximum diameter (<math>Dmax</math>) and half length (<math>L1/2</math>) are also investigated. Both <math>Dmax</math> and <math>L1/2</math> show an increasing then plateauing trend upon increasing <math>Fr</math> across different FFM cavitators despite the smaller values for the 3D cone cavitator. Subsequently, such cavity geometric information and cavity pressure measurements in conjunction with high speed imaging of re-entrant jet are employed to estimate the re-entrant jet momentum under different <math>Fr</math> for disk and cone cavitators. The estimated re-entrant jet momentum shows reasonable match with the ventilation air momentum under <math>CQc</math> in lower <math>Fr</math> for both cavitator cases, with the disk cavitator case yielding significantly stronger re-entrant jet, providing support to the re-entrant jet mechanism governing on the cavity collapse. Our study sheds some light on the cavitator design and ventilation strategy for a supercavitating vehicle in practice.

Cavity and hydrodynamic features of supercavitatingvehicle with conical cavitator

Water entry experiment of a cylindrical vehicle with disc cavitator

Effect of mounting strut and cavitator shape on the ventilation demand for ventilated supercavitation

Numerical analysis of cavitation and impact load characteristics of supercavitating vehicle entering water at high speed

Numerical Investigation on the Cavity Behavior and Hydrodynamic Performance of a Planing Air Cavity Ship

Experimental investigation of the underwater ventilated tail cavity at different angles of attack

Dynamics of the supercavitating hydrofoil with cavitator in steady flow field

Effects of Lateral Space and Angle of Attack on Ventilated Partial Cavity

Experimental and numerical study on flow dynamics and universal characteristics of ventilated supercavities behind different cavitators

Experimental and numerical analysis of the physical characteristics of natural and ventilated supercavitating flows

On the cavity flow of a cylinder exiting water obliquely

Experimental study on tail cavity structure and pressure characteristics of underwater vehicle with tail jet

Experiment Investigation of the Tip Vortex Cavitation Around a Pitching Hydrofoil

Cavity dynamics of vertical water entry of a truncated cone–cylinder body with different angles of attack

A Comparative Assessment of Various Cavitator Shapes for High-speed Supercavitating Torpedoes: Geometry, Flow-physics and Drag Considerations

Experimental research on jet induced tail cavities attached to underwater vehicles considering the influence of tail wings

Topology and cavitation number characteristics of the gaseous jet-induced tail cavity under co-flow

Finding optimal hull shapes for fast vertical penetration into water

Large Eddy Simulation Investigation of Micro-Vortex Generator Control Effect on Early Stage Sheet Cavitation

Experimental investigation of the dynamic evolution of cavity during the free water-exit of a high-pressure venting vehicle

Experimental and Numerical Investigation on the Cavity Regime and Drag Reduction of Ventilated Partial Cavity