Abstract:The present work systematically investigates the effect of cavitator mounting strut and cavitator shape on the ventilation demand to form and sustain a ventilated supercavity under different flow conditions. Three cavitators of different shapes (i.e. 2D cavitators including triangle and disk shape, and 3D cone-shaped cavitator) with the same frontal area are employed for the experiments. The cavitator is connected to a ventilation pipe extended upstream from a mounting strut, referred to as forward-facing model (FFM). The minimal ventilation coefficients to generate (<math>CQf</math>) and to collapse (<math>CQc</math>) a supercavity are measured over a wide range of Froude number (<math>Fr</math>) for each cavitator. Images of overall cavity shapes and topology near closure region as well as the cavity pressure under different experimental conditions are captured simultaneously. The results are compared across different cavitator shapes and the disk cavitator situated on the downstream side of the mount strut, referred to as backward-facing model (BFM). Similar <math>CQf-Fr</math> curves were observed in BFM and FFM-configured disk cavitators. The cone-shaped cavitator requires the least amount of ventilation to generate a supercavity among all different shapes across the range of <math>Fr</math> in our experiments. The <math>CQc</math>of disk FFM is lower than that of its BFM counterpart at small <math>Fr</math> and exceeds the BFM <math>CQc</math>with further increase of <math>Fr</math>. The cone cavitator has the smallest <math>CQc</math> among all the cavitators across the range of <math>Fr</math> in our experiments. To elucidate the trends of <math>CQc</math> upon changing <math>Fr</math> and cavitator shape, the geometry of supercavity under <math>CQc</math> including its overall shape, the cavity maximum diameter (<math>Dmax</math>) and half length (<math>L1/2</math>) are also investigated. Both <math>Dmax</math> and <math>L1/2</math> show an increasing then plateauing trend upon increasing <math>Fr</math> across different FFM cavitators despite the smaller values for the 3D cone cavitator. Subsequently, such cavity geometric information and cavity pressure measurements in conjunction with high speed imaging of re-entrant jet are employed to estimate the re-entrant jet momentum under different <math>Fr</math> for disk and cone cavitators. The estimated re-entrant jet momentum shows reasonable match with the ventilation air momentum under <math>CQc</math> in lower <math>Fr</math> for both cavitator cases, with the disk cavitator case yielding significantly stronger re-entrant jet, providing support to the re-entrant jet mechanism governing on the cavity collapse. Our study sheds some light on the cavitator design and ventilation strategy for a supercavitating vehicle in practice.

Experimental and Numerical Investigation on the Cavity Regime and Drag Reduction of Ventilated Partial Cavity

Experimental Investigation of Ventilated Partial Cavitation

Effects of Lateral Space and Angle of Attack on Ventilated Partial Cavity

Boundary layer analysis of ventilated partial cavity for friction drag reduction

Internal flows of ventilated partial cavitation

Numerical Study of Porous Tip Treatment in Suppressing Tip Clearance Vortices in Cavitating Flow

Numerical Investigation on the Cavity Behavior and Hydrodynamic Performance of a Planing Air Cavity Ship

Experimental investigation on interaction modes and geometric features of two ventilated cavities

Investigation on the internal flow of ventilated partial cavity

Experimental And Numerical Study Of Bubble Drag Reduction On A Flat Plate

Experimental and numerical study on flow dynamics and universal characteristics of ventilated supercavities behind different cavitators

Numerical Investigations of Pressure Distribution Inside A Ventilated Supercavity

Effect of the Gust Wave on the Dynamic Behavior of Cavity Closure and Pressure: A Numerical Study

Experimental and numerical analysis of the physical characteristics of natural and ventilated supercavitating flows

Numerical Study of Solid Particle Erosion in a Cavity with Different Wall Heights

Simulation-based Study of Low-Reynolds-number Flow Around a Ventilated Cavity

Numerical Study on the Vertical Water Exit of A Cylinder with Cavity

Effect of mounting strut and cavitator shape on the ventilation demand for ventilated supercavitation

Numerical study of the behaviors of ventilated supercavities in a periodic gust flow

Flow pattern regime and unsteady characteristics of ventilated cavitating flow around the axisymmetric bodies with different headforms

Experimental investigation of the dynamic evolution of cavity during the free water-exit of a high-pressure venting vehicle