Abstract:The present work systematically investigates the effect of cavitator mounting strut and cavitator shape on the ventilation demand to form and sustain a ventilated supercavity under different flow conditions. Three cavitators of different shapes (i.e. 2D cavitators including triangle and disk shape, and 3D cone-shaped cavitator) with the same frontal area are employed for the experiments. The cavitator is connected to a ventilation pipe extended upstream from a mounting strut, referred to as forward-facing model (FFM). The minimal ventilation coefficients to generate (<math>CQf</math>) and to collapse (<math>CQc</math>) a supercavity are measured over a wide range of Froude number (<math>Fr</math>) for each cavitator. Images of overall cavity shapes and topology near closure region as well as the cavity pressure under different experimental conditions are captured simultaneously. The results are compared across different cavitator shapes and the disk cavitator situated on the downstream side of the mount strut, referred to as backward-facing model (BFM). Similar <math>CQf-Fr</math> curves were observed in BFM and FFM-configured disk cavitators. The cone-shaped cavitator requires the least amount of ventilation to generate a supercavity among all different shapes across the range of <math>Fr</math> in our experiments. The <math>CQc</math>of disk FFM is lower than that of its BFM counterpart at small <math>Fr</math> and exceeds the BFM <math>CQc</math>with further increase of <math>Fr</math>. The cone cavitator has the smallest <math>CQc</math> among all the cavitators across the range of <math>Fr</math> in our experiments. To elucidate the trends of <math>CQc</math> upon changing <math>Fr</math> and cavitator shape, the geometry of supercavity under <math>CQc</math> including its overall shape, the cavity maximum diameter (<math>Dmax</math>) and half length (<math>L1/2</math>) are also investigated. Both <math>Dmax</math> and <math>L1/2</math> show an increasing then plateauing trend upon increasing <math>Fr</math> across different FFM cavitators despite the smaller values for the 3D cone cavitator. Subsequently, such cavity geometric information and cavity pressure measurements in conjunction with high speed imaging of re-entrant jet are employed to estimate the re-entrant jet momentum under different <math>Fr</math> for disk and cone cavitators. The estimated re-entrant jet momentum shows reasonable match with the ventilation air momentum under <math>CQc</math> in lower <math>Fr</math> for both cavitator cases, with the disk cavitator case yielding significantly stronger re-entrant jet, providing support to the re-entrant jet mechanism governing on the cavity collapse. Our study sheds some light on the cavitator design and ventilation strategy for a supercavitating vehicle in practice.

INFLUENCE OF CAVITATOR PARAMETERS ON FORMATION AND DEVELOPMENT OF SUPERCAVITY

Experimental Investigation of Ventilated Partial Cavitation

Experimental and numerical analysis of the physical characteristics of natural and ventilated supercavitating flows

Experimental and numerical study on flow dynamics and universal characteristics of ventilated supercavities behind different cavitators

Effect of mounting strut and cavitator shape on the ventilation demand for ventilated supercavitation

Experimental and Numerical Investigation on the Cavity Regime and Drag Reduction of Ventilated Partial Cavity

Numerical Investigations of Pressure Distribution Inside A Ventilated Supercavity

Investigation into the behaviors of ventilated supercavities in unsteady flow

The experimental and numerical studies of formation and collapse processes of ventilated supercavitating flow

Numerical study of the behaviors of ventilated supercavities in a periodic gust flow

Insights into ventilation hysteresis shift due to flow unsteadiness in ventilated supercavitation

Flow pattern regime and unsteady characteristics of ventilated cavitating flow around the axisymmetric bodies with different headforms

Experimental investigation on interaction modes and geometric features of two ventilated cavities

Experimental research on supercavitation in jet pump cavitation reactors for zero flow-ratio conditions

Experimental investigation of cavitating flow around chamfered cylinders vertically inserted in a circular pipe

Dynamics of the supercavitating hydrofoil with cavitator in steady flow field

Shear layer on a ventilated supercavity wall

Probing into gas leakage characteristics of ventilated supercavity through bubbly wake measurement

Control Effect of Micro Vortex Generators on Leading Edge of Attached Cavitation

Experiment Investigation of the Tip Vortex Cavitation Around a Pitching Hydrofoil

Numerical Investigation of the Cavitation Characteristics in Venturi Tubes: The Role of Converging and Diverging Sections