Abstract:This study investigates the application of ultrasound-assisted pulse electrodeposition (ULSPE) to prefabricate Ni-W-SiC composite coatings onto Q235-steel samples. The surface and cross-sectional morphology, phase composition and wear performance of the resulting coatings were analyzed by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM). Furthermore, the nanocoatings were evaluated for hardness and corrosion resistance using microhardness (MH) measurements and electrochemical analysis. Among the samples, the Ni-W-SiC coating deposited at 20 W/cm 2 demonstrated improved properties, including a highly uniform and compact structure with porosity as low as 0.07 %. Increasing the ultrasonic power density (UPD) from 0 to 20 W/cm 2 during the ULSPE process resulted in an increase in SiC content within the coating from 6.21 wt% to 7.54 wt%. At 20 W/cm 2 , the Ni-W-SiC coating demonstrated SiC particles with an average size of 45.3 nm. Among all tested coatings, the one deposited at 20 W/cm 2 showed the broadest and weakest diffraction peaks, reflecting its refined nanostructure, and achieved the highest microhardness of 743.9 HV. The corrosion current density at this power density level was determined at 1.84 × 10 −6 A/cm 2 , which was approximately one-eleventh of the value for Q235 steel, demonstrating exceptional corrosion resistance. XPS analysis revealed the oxidation states of Ni, W, and SiC, confirming the successful incorporation of SiC particles into the matrix and the formation of protective oxide layers. The higher corrosion resistance of the coating at 20 W/cm 2 was further validated by electrochemical impedance spectroscopy.

Study on Preparation and Properties of Nano Ni-SiC Amorphous Composite Coatings

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

Microstructure evolution, mechanical and abrasive wear properties of NiCrSiB-SiC composite coatings prepared on 16Mn low-carbon steel by Ni-based alloy catalyzed SiC decomposition

Preparation and Properties of Ni–Co–P/nano‐sized Si3N4 Electroless Composite Coatings

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Electroless Ni-P-Sic Composite Coatings with Superfine Particles

Effect of SiC Nanoparticles on the Structure and Properties of Ni+W-SiC Nanocoatings

Impact of ultrasonic power density on the structure and performance of Ni-W-SiC composite nanocoatings

Preparation of Ni-P-SiC Electroless Composite Coating with High Wear and Corrosion Resistance

Effect of SiC Contents on Wear Resistance Performance of Electro-Codeposited Ni-SiC Composite Coatings

Investigation on Microstructure and Properties of the Electrodeposited Ni-SiC Composite Coating

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Comparative study on the wear resistance and corrosion resistance of NiW and NiCoW composite coatings with micro- and nano-SiC particles

Microstructure and Mechanical Properties of Ni-P/SiC,Ni-P/WC Nano-composite Coatings Prepared by Electro-brush Plating

Study on Microstructure and Properties of Ni- Al2O3 Composite Coating

Study of fabrication and wear properties of Ni–SiC composite coatings on A356 aluminum alloy

Preparation and Characterization of Pulse Electrodeposited Ni/W-SiC Nanocomposite Coating on Mild Steel Substrate

Structure and performance of brush-electroplated nickel-based nano SiC-Al2O3 composite coating