Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Influences of Strontium Addition and Whisker Content on Solidification Behavior of Sic(W)/Al-18si Metal Matrix Composites

Investigation on the Primary Si Phase Solidification and the Properties of Sicw/Al-18si Composites

Solidification behavior of SiCw/Al-18Si composites

Effect of modification and ceramic particles on solidification behavior of aluminum-matrix composites

Effect of Cooling Rate on the Solidification Behavior and Microstructure of SiC_w/Al-18Si Composites

Mechanical Properties and Microstructure of Calcium Sulfate Whisker-Reinforced Cement-Based Composites

Mechanical Properties of Silicon Carbide Whisker-Reinforced Silicon Nitride Matrix Composites

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

The Effect of Sintering Additive on Fracture Behavior of Carbon-Whisker-reinforced Silicon Carbide Composites

Effects of Strontium Impurity on the Structure and Dynamics of Al88si12 Liquid

Preparation and mechanical properties of SiC whisker-reinforced alumina

The Dual Effect Of Whiskers On Toughening And Conducting Properties In Aligned Sic Whisker-Reinforced Si3n4-Matrix Composites

Synergistic Effect of Strontium and Melt Quenching on the Solidification Microstructure of Hypereutectic Al-Si Alloys

The effect of whisker misalignment on the hot compressive deformation behavior of SiCw/6061 Al composites at 500°C

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

The effect of SiC whisker on the performances of Al2O 3 matrixceramics mould for hollow turbine blade

Microstructural Changes of SiCw/6061Al Composite During Compression at Temperatures below and above the Solidus of the Matrix Alloy

The preparation of mullite foamed ceramics reinforced by in-situ SiC whiskers and their reinforcement mechanism

Effect of strontium and melt purification on the solidification microstructure of hypereutectic Al-Si alloys

Interface Structure and Mechanical Properties of Al2O3–20vol%SiCw Ceramic Matrix Composite

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy