Abstract:Three types of inorganic fillers - fumed nonporous nano-silica, synthesized mesoporous MCM-41 and microporous zeolite 4A, were incorporated into the PVDF matrix to prepare mixed matrix membranes. The objective of this study was to investigate the effects of pore structure and particle size of the inorganic fillers on the gas transport properties of the mixed matrix membranes. The membranes were characterized using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC). X-ray diffraction (XRD), contact angle tests and scanning electron microscopy (SEM). The mechanical properties of the membranes were determined using a tensile stress-strain machine. With the incorporation of the inorganic fillers, the thermal stability of the composite membranes was reduced with lower degradation temperature while the melting temperature and crystallizing temperature seemed to be unaffected. The DSC results showed that the crystallinity of the composite membranes had increased when compared with the pure PVDF membrane. In addition, the incorporation of MCM-41 had induced PVDF crystalline phase transformation from alpha to beta phase. This phenomenon was not observed in PVDF/SiO2 and PVDF/4A composite membranes as indicated by the XRD results. In order to fully study the interface properties between the inorganic fillers and polymer chains, the density values of the membranes were experimentally determined and compared with the theoretical values. The experimentally determined density values of the composite membranes were lower than the theoretical values and the void volume fractions were calculated accordingly. The single gas (He, CO2, O-2 and N-2) permeabilities of the resulting membranes were carried out. The gas permeabilities of the three composite membranes exhibited similar behaviors, especially at lower inorganic filler loadings, although the inorganic fillers had different pore structures and particle sizes. The highest permeabilities for CO2 and O-2 were obtained by PVDF/4A 32% composite membrane, which were 3.26 and 0.41 Barrer, respectively, and the highest permeabilities for He and N2 were obtained by PVDF/MCM-41 32% composite membrane, which were 10.2 and 0.14 Barrer, respectively. These permeabilities are much higher than those of pure PVDF membrane. The highest selectivities of 120.7, 33.1 and 4.6 for He/N-2, CO2/N-2, and O-2/N-2, were obtained by the PVDF/SiO2 4%, PVDF/SiO2 32% and PVDF/SiO2 24%, respectively, which are also higher than those of pure PVDF membrane. (C) 2012 Elsevier B.V. All rights reserved.

Influence of Molecular Structure of Precursors on Microstructure and Gas Separation Performance of Carbon Membranes Derived from Poly (furfuryl Alcohol)

Tuning the gas transport performance of carbon molecular sieve membranes by the morphological changes of 6FDA/PMDA-TMMDA precursors

Preparation and characterization of novel carbon molecular sieve membrane/PSSF composite by pyrolysis method for toluene adsorption

Thin Composite Carbon Molecular Sieve Membranes from a Polymer of Intrinsic Microporosity Precursor

Preparation of Free-Standing High Quality Mesoporous Carbon Membranes

Gas separation of pyrolyzed polymeric membranes: Effect of polymer precursor and pyrolysis conditions

Research on Formation and Gas Separation Performance of Polyetherimide Based Carbon Molecular Sieve Membranes

Casting Solvent Effects on Morphologies, Gas Transport Properties of a Novel 6FDA/PMDA?TMMDA Copolyimide Membrane and Its Derived Carbon Membranes

Effects of Preparation Parameters on CO2/N-2 Gas Permselectivity of Polyether Thin Film Composite Membrane

Preparation of a PVA/Chitosan/Glass Fiber Composite Membrane and the Performance in CO2 Separation

Synergistic Tuning of Microstructure and Morphology in Carbon Molecular Sieve Hollow Fibers for Propylene/Propane Separation

Carbon Molecular Sieve Membrane Preparation by Economical Coating and Pyrolysis of Porous Polymer Hollow Fibers

Tailoring the Stabilization and Pyrolysis Processes of Carbon Molecular Sieve Membrane Derived from Polyacrylonitrile for Ethylene/Ethane Separation

The evolution of the structure, mechanical, and gas separation properties of P84 hollow fiber membranes from the polymer to the carbon stage

Processing-structure-property correlations of polyethersulfone/perfluorosulfonic acid nanofibers fabricated via electrospinning from polymer-nanoparticle suspensions.

Polymide/Fe_3O_4-carbonized Membranes for Gas Separation

Direct Thermal Oxidative Cross-Linking in Air Toward Hierarchically Microporous Polymer Membranes for Advanced Molecular Sieving

Influence of NIPS on the structure and gas separation performance of asymmetric carbon molecular sieve membranes

Preparation and Characterization of Mixed Matrix Membranes Based on PVDF and Three Inorganic Fillers (fumed Nonporous Silica, Zeolite 4A and Mesoporous MCM-41) for Gas Separation

Effect of polytetrafluoroethylene hollow fiber microstructure on formaldehyde carbonylation performance in membrane contactor

Pyrolytic Carbon Membranes Containing Silica: Morphological Approach on Gas Transport Behavior