Abstract:Water concentration inside proton exchange membrane fuel cells (PEMFCs) is a key factor affecting performance and durability. Therefore, many studies have been conducted to maintain an appropriate moisture balance inside the stack. The most recent study was a study that confirmed moisture distribution using five sensors inside the anode and cathode. However, in this study, it is difficult to determine the exact moisture distribution inside the stack due to insufficient sensors. In this study, a unit cell PEMFC including micro relative humidity and temperature (RH/T) sensors with an active area of 100cm 2 was fabricated to characterize the water concentration. Before installing the micro sensors into the bipolar plates, a reliability test is conducted, and the result shows that the sensor is reliable at 60 °C and 70 °C. After that, for the in-situ temperature and relative humidity measurement, the 50 sensors are installed along the anode and cathode gas channels evenly in the active area. This study investigates the distribution of water transport behavior, temperature, and water concentration at 0.6 V, 0.5 V and 0.4 V of electric load. Dew point is introduced to analyze water concentration, and net water mole flux is calculated to evaluate water transport behavior. The results show that as the load applied to the PEMFC increases, higher temperature band expands from downstream to upstream of the gas flow. In addition, at 0.4 V, observing the highest temperature band between 61 °C to 62 °C, it is concluded that the flow field of the reaction zone is more activated along the downstream. Meanwhile, the anode becomes more dehydrated with higher load and the cathode more hydrated. At 0.4 V, the maximum dew point on the cathode is 37.5 °C, and the minimum dew point on the anode is 30 °C. In conclusion, even though water transports from the cathode to the anode, due to dry inlet gas, 20% of relative humidity, and high flow rate, hydrogen by 2.8lpm and air by 6.65lpm, the anode doesn't become hydrated.

Design and Stability of Reference Electrode in Direct Methanol Fuel Cell

Study on stability of self-breathing DFMC with EIS method and three-electrode system

Comparative Studies of Configurations and Preparation Methods for Direct Methanol Fuel Cell Electrodes

Uncoupling Characteristics Of Temperature And Relative Humidity Distribution In A Commercial-Size Polymer Electrolyte Membrane Fuel Cell

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell

Multiple in-situ measurement of water transport in the bipolar plate of proton exchange membrane fuel cell

Effect of RuO2·xH2O in Anode on the Performance of Direct Methanol Fuel Cells

Experimental Measurements of Fuel and Water Crossover in an Active DMFC

Polarization Distribution and Theoretical Fitting of Direct Methanol Fuel Cell

Enhancement of Water Retention in the Membrane Electrode Assembly for Direct Methanol Fuel Cells Operating with Neat Methanol

Design and Performance Analysis of an Air-Breathing Micro Direct Methanol Fuel Cell

Durability of Direct Internal Reforming of Methanol As Fuel for Solid Oxide Fuel Cell with Double-Sided Cathodes

A Liquid–Vapor Two-Phase Model of Direct Methanol Fuel Cells With Platinum Group Metal-Free Cathode Catalyst

Design, Fabrication and Testing of an Air-Breathing Micro Direct Methanol Fuel Cell with Compound Anode Flow Field

Design, Fabrication and Testing of a Silicon-Based Air-Breathing Micro Direct Methanol Fuel Cell

A Solid Electrolyte RHE for Electrode Diagnosis of Proton Exchange Membrane Water Electrolyzers

Design and Fabrication of a Silicon-Based Direct Methanol Fuel Cell with a New Cathode Spoke Structure

Designing Membrane Electrode Assembly for Weakly Humidity-Dependent Proton Exchange Membrane Fuel Cells

Design and Utilization of a Direct Methanol Fuel Cell

In-situ Measurement of Temperature and Humidity Distribution in Gas Channels for Commercial-Size Proton Exchange Membrane Fuel Cells

Numerical Investigations of Effect of Membrane Electrode Assembly Structure on Water Crossover in A Liquid-Feed Direct Methanol Fuel Cell