Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Studies on Thermal Conductivity of Methyl Methacrylate Bulk Polymerization System

Measurement and Correction of Physical Property Parameters of Methyl Methacrylate Bulk Polymerization System

INFLUENCE OF MONOMER COMPOSITION ON THE CHAIN TRANSFER COEFFICIENT IN METHYL METHACRYLATE/BUTYL ACRYLATE RAFT COPOLYMERIZATION

Thermal Safety and Overall Kinetics for Methyl Methacrylate Solution Polymerization via On-line Process Analytical Technology

Free-radical Crosslinking Copolymerization of Methyl Methacrylate/Triallyl Isocyanurate

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Relationship Between Dielectric Behaviors and Conversion of Mma During Polymerization Process

Temperature effect on polymerization kinetics of poly methyl methacrylate (PMMA)

Kinetics of Suspended Emulsion Polymerization of Methyl Methacrylate

Measuring in-plane thermal conductivity of polymers using a membrane-based modified Ångström method

The Use Of Epsilon-Caprolactone As A Polymerizable Solvent For The Atom Transfer Radical Polymerization Of Mma At Low Temperature

Kinetic and Molecular Weight Control for Methyl Methacrylate Semibatch Polymerization. II. Open Control

Fundamental Study on Preparation Process and Structure Coutrol of PBA/PMMA

Irradiation of Low Intensity Ultrasonic to Initiate the Bulk Polymerization of MMA

The Effect of the Chain Length on Mma Free Radicl Polymerization

Kinetics Model and Simulation for Bulk Polymerization of Methyl Methacrylate

Study on Dielectric Monitoring on Polymerization Process of MMA

Kinetics Study of Methyl Methacrylate Bulk Polymerization

Effect of Temperature on Copolymerization Parameters of Hydroxyethyl Acrylate and Methyl Methacrylate

Monitoring dispersion polymerisations of methyl methacrylate in supercritical carbon dioxide

Study on bulk polymerization of methyl methacrylate initiated by low intensity ultrasonic irradiation