Abstract:High performance engineering thermoplastics modified epoxy resins are novel materials avoiding the usual shortcomings of rubber modification (i.e., reduction of glass transition temperature, yield strength, and elastic modulus), and having improved impact strength and fracture toughness [1, 2]. Although the use of thermoplastic modifier has been important for the improvement of fracture toughness is a mechanical property high performance epoxy resins, there is limited information concerning the interfacial control between thermoplastic modifier and epoxy resins [3]. And in most cases, commercial thermoplastics are directly used as modifiers without effective control of the interface between the dispersed phase and the cured epoxy resin. There are two ways to improve the interfacial adhesion between the dispersed thermoplastics phase and the cured epoxy resin. The first is to chemically modify or functionalize the thermoplastics modifier. The second is to introduce mutual interaction, such as dipole-dipole interaction, hydrogen-bonding etc., into the curing system to improve the compatibility. Recent studies have shown that the interfacial adhesion between thermosets and thermoplastics can be dramatically improved when interdiffusion is possible [4]. Here, we prefer the second way since the development of functional polymers is still limited to the laboratory and it is a high cost process. This paper reports the incorporation effect of a second thermoplastics modifier (PC), on the phase separation behavior and morphology of PEI modified E-51 curing systems by using small angle laser light scattering (SALLS) and scanning electron microscopy (SEM, Hitachi S-570). The samples were made by incorporating various contents of polyetherimide (PEI; General Electric Co., USA) and polycarbonate (PC, based on bisphenonl-A; Idenitsu Kosan Co., Japan) into E-51 (a commercial grade epoxy resin based on diglycidyl ether of bisphenonl-A; Hangzhou Chemical Plant China) by weight. Then cured with 4,4 � diamino-diphenylsulphone (DDS; Chemical agent Co., China).

EFFECT OF DIOCTYLPHTHALATE AS PLASTICIZER ON THE PERFORMANCES OF UV CURABLE ADHESIVE

Plasticizer Effect of Dibutyl Phthalate on the Morphology and Mechanical Properties of Hard Elastic Poly(Vinylidene Fluoride) Fibers

Effects of Active Diluents on Solidifying Process of UV-curing Reaction for Polyurethane Acrylate

Studies on the influence of soft-segment structure on the properties of polyurethane adhesive

Effects of Dibenzocrown Ether and Diphenoxyethylene Diether Structural Units on the Properties of Degradable Polyhexahydrotriazine Thermosetting Resins

Improved Processing and Properties for Polyphenylene Oxide Modified by Diallyl Orthophthalate Prepolymer

Thermoplastic polyurethane-based polycarbonate diol hot melt adhesives: The effect of hard-soft segment ratio on adhesion properties

Research on the Glass Transition Temperature and Mechanical Properties of Poly(vinyl chloride)/Dioctyl Phthalate (PVC/DOP) Blends by Molecular Dynamics Simulations

The Effect Of Diisocyanate Isomer Composition On Optical And Adhesive Properties Of Polyurethanes Based On 4,4 '-Dicyclohexyl Methane Diisocyanate

Study on Preparation and Performance of Reactive Polyurethane Hot Melt Adhesives Based on a Polycarbonate Diol and a Polyester Diol

Effect Of Chain Extender On Adhesive And Optical Properties Of Transparent Polyurethane Elastomers

Enhancing adhesive strength and durability: Exploring the benefits of upconversion particle-assisted near-infrared photopolymerization

Using an Inhibitor to Prevent Plasticizer Migration from Polyurethane Matrix to EPDM Based Substrate

Effect of double bond position and density on properties of UV-induced bio-based polyurethane adhesion-reducing adhesives

UV‐photopolymerized acrylic pressure‐sensitive adhesives with semi‐interpenetration structure: Effect of plasticizer structures on adhesion properties

Preliminary investigation of a second thermoplastic modifier incorporation effect on the phase behavior and morphology of epoxy/PEI curing systems

Effects of curing temperature on the structure and properties of epoxy resin-poly(ε-caprolactam) blends

Role of the Soft and Hard Segments Structure in Modifying the Performance of Acrylic Adhesives Modified by Polyurethane Macromonomers

A novel CO 2 based UV-induced peelable adhesive for wafer dicing

Effect of proanthocyanidins and photo-initiators on photo-polymerization of a dental adhesive

Hydrogenation induced deviation of temperature and concentration dependences of polymer-solvent interactions in poly(vinyl chloride) and a new eco-friendly plasticizer