Abstract:We report observation of ring-shaped morphology formed in thin films of a cylinder-forming polystyrene-b-poly(methyl methacrylate) (PS-b-PMMA) diblock copolymer cast from 1,1,2,2-tetrachloroethane (Tetra-CE) solution via relatively fast solvent evaporation rates, in which Tetra-CE is a good solvent for both blocks but preferential affinity for the minority PMMA block. We studied the microstructure of a set of solution-cast block copolymer films dried with different solvent evaporation rates, R. The control with different R leads to keeping microstructures in different solution concentrations (phi) and bringing mechanical strain fields with different strength in the film, for which faster evaporation rates result in microstructures of lower solution concentrations and mechanical strain fields of higher strength. As R decreases from rapid evaporation (approximately 0.1 mL/h), the film microstructure evolved from an intermediate ringlike morphology sequentially to ring-shaped morphologies including loose and tight rings and then inverted phase of PS spheres in a PMMA matrix and finally reached the equilibrium phase, namely, cylinders of PMMA in a PS matrix. In view of the influence of the film constraints, the microstructure of a film with a terraced free surface profile has been examined. The results indicate that the ring-shaped morphology can form as long as the film thickness is larger than a critical value of about one microdomain spacing. In the case where the film thickness is larger than that value, the nature of solvent and the kinetics of solvent evaporation are shown to be mainly responsible for the ring-shaped morphology formation.

Studies on the Surface Morphology of Poly (Styrene-B-dimethylsiloxane) Copolymer Thin Films

Morphology of poly(styrene-block-dimethylsiloxane) copolymer films

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Effect of the Nature of Annealing Solvent on the Morphology of Diblock Copolymer Blend Thin Films

Morphologies in Acetone-Annealed Polystyrene-Poly(Methyl Methacrylate) Diblock Copolymer Thin Films

Surface Morphology Evolution of Poly (Styrene-Block-4-vinylpyridine) (Ps-B-p4vp)(h+) and Poly(Methyl Methacrylate)-Dibenzo-18-Crown-6-Poly(Methyl Methacrylate) (pmcma) Supramolecular Film

Morphologies in Solvent-Annealed Thin Films of Symmetric Diblock Copolymer

Solvent Dependence of the Morphology of Spin-Coated Thin Films of Polydimethylsiloxane-Rich Polystyrene- block -Polydimethylsiloxane Copolymers

Nanoscopic surface patterns of diblock copolymer thin films

Surface Microphase Separation in PDMS‐b‐PMMA‐b‐PHFBMA Triblock Copolymer Films

Morphology Development Of Ultrathin Symmetric Diblock Copolymer Film Via Solvent Vapor Treatment

Microphase Separation Behavior on the Surfaces of Poly(Dimethylsiloxane)-Block-Poly(2,2,3,3,4,4,4-Heptafluorobutyl Methacrylate) Diblock Copolymer Coatings

Constructional details of polystyrene-block-poly(4-vinylpyridine) ordered thin film morphology

Lamellar Morphology in Block Copolymers of Polystyrene and Poly[methyl(3,3,3-trifluoropropyl)siloxane]

Phase structural formation and oscillation in polystyrene-block-polydimethylsiloxane thin films

Ring-shaped Morphology in Solution-Cast Polystyrene-Poly(methyl Methacrylate) Block Copolymer Thin Films.

Synthesis and Surface Characterization of Poly(methyl Methacrylate)‐block‐polydimethylsiloxane Copolymers from Macroazoinitiator

Monte Carlo Simulation of Ab Diblock Copolymer Between Surface and Substrate and Comparison of Experimental Results

Morphology of Films of SEBS Triblock Copolymers

Effect of Added Homopolymer on Structures of Thin Films of PS-b-PDMS/PS Mixture under Solvent Vapor Annealing

Water-induced Morphology Evolution of Block Copolymer Micellar Thin Films