Abstract:This paper investigates the buckling behaviour and load-carrying capacity of G550 high strength cold-formed steel built-up section columns under axial compression through experiments and numerical simulations. Two types of built-up sectional profiles were formed, which were defined as built-up OI-section and built-up CB-section. Each built-up OI-section member is formed by connecting two cold-formed steel C-section members in a back-to-back manner using self-drilling screws, while each built-up CB-section member consists of a cold-formed steel C-section member and a cold-formed steel U-section member, which are connected in a face-to-face manner by self-drilling screws. The experimental programme included tensile coupon tests, initial geometric imperfection measurements and 20 pin-ended column compression tests. In the numerical modelling programme, finite element models were developed and validated against the experimental results, and then used for parametric analyses to generate a total of 250 numerical data with different cross-section dimensions and member lengths. Based on the experimental and numerical data, the accuracy of both the effective width method and the direct strength method for predicting the strengths of G550 high strength cold-formed steel built-up section columns, as set out in the American Specification, was evaluated. The evaluation results indicated that both the effective width method and direct strength method provided accurate and consistent failure load predictions for G550 high strength cold-formed steel built-up OI-section columns on average, but with some unsafe failure load predictions, while the predicted failure loads were inaccurate, scattered and conservative for G550 high strength cold-formed steel built-up CB-section columns. Moreover, the effective width method and direct strength method yielded a similar level of design consistency for G550 cold-formed steel built-up section columns, but the direct strength method resulted in more accurate and less conservative failure load predictions than the effective width method. The modifications to the codified DSM equations were proposed for G550 high strength cold-formed steel built-up section columns and shown to provide improved predictions of failure load over the design codes.

Reliability Analysis of 550mpa High-Strength Cold-Formed Thin-Walled Steel Structures

Reliability-based design on centrifuge concrete filled steel tubular members

Testing, numerical modelling and design of G550 high strength cold-formed steel built-up section columns

Design of Cold-Formed Steel Built-Up Closed Sections with Intermediate Stiffeners

LOCAL BUCKLING OF THIN-WALLED HIGH STRENGTH STEEL COLUMNS WITH WEB STIFFENERS

Cold-formed steel lipped channel columns at elevated temperatures

FINITE ELEMENT ANALYSIS AND DESIGN METHOD STUDY ON THE LOCAL BUCKLING OF 460 MEGAPASCAL HIGH STRENGTH STEEL I-SECTION COLUMNS UNDER AXIAL COMPRESSION

Finite Element Analysis on the Local Buckling Behavior of High Strength Steel Members under Axial Compression

Research On Resistance Model Uncertainty Of High Strength Steel Axial Compression Members

STUDY ON THE STABILITY DESIGN METHOD OF HIGH STRENGTH STEEL ANGLE MEMBERS UNDER AXIAL COMPRESSION

Experimental and Analytical Study on Local Buckling Behavior of High Strength Steel Welded I-Section Beams

Experimental investigation on axial compression behaviour of cold-formed thick-walled steel tubes

RESEARCH ON RESISTANCE MODEL UNCERTAINTIES OF HIGH-STRENGTH STEEL MEMBERS SUBJECTED TO COMBINED AXIAL LOAD AND BENDING AND FLEXURAL MEMBERS

Experiment and Design Method of Cold-Formed Thin-Walled Steel Double-Lipped Equal-Leg Angle under Axial Compression

Local buckling behaviour of welded I-section steel stub columns with longitudinally profiled steel plates under axial compression: Testing, modelling and design

Local and Global Interactive Buckling Capacity of Thin-Walled Box-Section Members of BS700 High-Strength Steel under Axial Compression

Investigations and proposed design rules on bolted connections for high strength steel

Numerical Study and Design Method for Lateral Torsional Buckling of High-Strength Steel Beams

COMPARATIVE STUDY ON DESIGN METHODS FOR LOCAL STABILITY OF HIGH STRENGTH STEEL FLEXURAL MEMBERS IN DIFFERENT CODES

Comparative Study On Design Methods For Steel Structural Members Strengthened By Increasing The Section Area While Under Load In Different Codes

Analysis and Design Method on Local Buckling Behavior of 960 MPa High Strength Steel Columns under Axial Compression