Abstract:This paper is an overview of the progress of sol-gel autocombustion synthesis of metals and metal alloys. Sol-gel is a convenient method to synthesize a variety of oxides by mixing of different elements at an atomic level. Autocombustion synthesis is a self-sustaining process caused by the heat generated from its exothermic reaction. By combining these two methods, the sol-gel autocombustion method is introduced in the synthesis of metals and metal alloys. The experimental principle and technological route are introduced in detail in this review. By using metal nitrate, citric acid etc. as starting materials, the dried gels are prepared through sol-gel routine. Under the protection of inert gas, the autocombustion could be activated at low temperature in a tube furnace. After the autocombustion was activated, the gel burned violently, and a large amount of white gas was released. During heating the gel, mass spectrum shows that the H-2, CO and CH4 are evidently identified near the combustion temperature. They are well known reducing agents, which can be used in the redox reaction for synthesizing metals from oxides. Based on the data obtained from the TG-DTA and mass spectrum analysis, it is speculated that there are mainly five reactions appearing during the burning of the gel at high temperature: exothermic reaction between fuel and oxidant; metal oxide(s) formation by decomposition of the nitrate(s); generation of CH4, CO and H-2 by the decomposition of CHx containing groups of complexing agent; exothermic reaction between CH4/ CO/ H-2 and oxidant; the reduction of metals from their corresponding metal oxides by CH4 and H-2 in nascent product. The application of this method to the synthesis of metals and metal alloys is shown by realized examples. This method shows many advantages in the synthesis of metals, such as simple apparatus, inexpensive raw materials, a relatively simple preparation process, and fine powder products with high homogeneity. Moreover, very low temperature is required to activate the reaction, and then the combustion can continue to take place without needing additional energy supply. This method has potential applications in experimental material researches.

Synthesis of ultrafine MgAl2O4 powders by sol-gel auto ignition

Self-propagating High-temperature Synthesis and Reaction Mechanism of Super-fine Particles of γ-LiAlO2

Synthesis of nanometer Ni-Zn ferrite powders by sol-gel auto-combustion

Self-propagating high-temperature synthesis and reaction mechanism of super-fine particles of gamma-LiAlO2

Synthesis of Nano-Alumina Hydroxide Sol Using Sol-gel Method

Effects of chelation reactions between metal alkoxide and acetylacetone on the preparation of MgAl2O4 powders by sol-gel process

Effect of Synthetic Parameters on Synthesis of Magnesium Aluminum Spinels

Synthesis of α-Al2O3 Nanopowders at Low Temperature from Aluminum Formate by Combustion Process

Synthesis Of Nicuzn Ferrite Nano-Sized Particles By Sol-Gel Auto-Combustion

Synthesis of BiFeO3-PbTiO3 powders by sol-gel auto-combustion process

Preparation and Characterization of Mg-Al-B Alloy (Mg0.5Al0.5B2) Via High-Temperature Sintering

Synthesis of nanocrystalline NiCuZn ferrite powders by sol–gel auto-combustion method

Novel Synthesis of High Surface Area MgAl2O4 Spinel As Catalyst Support

Progress in Sol-Gel Autocombustion Synthesis of Metals and Alloys

Synthesis of Nanocrystalline LaFeO3 by Sol-gel Auto- combustion Method

Research and Progress of Sol-gel Auto-Combustion Process in the Synthesis of Nanomaterials

Effect of Precursor Solutions with Different Composition on Synthesis of Ultrafine BaLa0.3Fe11.7O19using Sol-Gel Auto-Combustion Technique

Synthesis of nanocrystilline ferrites by sol–gel combustion process: the influence of pH value of solution

A Simple Way to Prepare Nanosized LaFeO 3 Powders at Room Temperature

Combustion synthesis of NiAl2O4 spinel powder

Room Temperature Preparation of Nanocrystalline MnCuZn Ferrite Powder by Auto-Combustion of Nitrate-Citrate Gels