Abstract:Microbumps play a crucial role in interlayer interconnections for advanced packaging. Among the prevalent microbump structures are Cu/Sn and Cu/Ni/Sn configurations. However, as the bump size continues to shrink, excessive Kirkendall voids tend to form in Cu/Sn microbumps, leading to potential reliability issues. While Cu/Ni/Sn structures can suppress Kirkendall void formation, Ni3Sn4 intermetallic compound (IMC) exhibits inferior physical properties compared to Cu3Sn and Cu6Sn5. In this study, a novel Cu/Ni/Cu/Sn1.8Ag (CNCT) Sn-rich microbump structure with controlled Cu thickness is proposed to suppress Kirkendall void formation while promoting Cu6Sn5 and Cu3Sn as interfacial IMCs. A Ni barrier layer is inserted to partition the Cu pillar and impede Cu atom replenishment from the bottom side. The remaining Cu pillar at the top is designed to be 3μm thick, which is intended to be fully consumed by 8μm Sn1.8Ag solder while simultaneously serving as redundant protection for the bottom Cu pillar against unexpected Sn spillage. The effects of high temperature storage (HTS) at 150°C on IMC evolution in CNCT microbump bonding were investigated for 1500hours. No significant voids were observed at the bonding interface during HTS. Interfacial positions recorded from 0 to 500hours show that the Cu3Sn IMC grows unidirectionally toward the Cu side but not toward the Sn side, indicating a greater diffusion flux of Sn atoms compared to Cu atoms. The diffusion coefficients of Cu in Cu3Sn (DCu,ε), Cu6Sn5 (DCu,η), and Sn in Cu3Sn (DSn,ε), Cu6Sn5 (DSn,η) at 150°C were calculated as 1.36×10-18m2/s, 5.01×10-19m2/s, 9.53×10-19m2/s and 1.10×10-18m2/s, respectively. The dramatic decrease of DCu,η suggests that the diffusion capacity of Cu atoms into Sn is significantly suppressed. The notable transformation of Cu3Sn to Cu6Sn5 occurred after 500hours. By 1500hours, Cu3Sn was greatly consumed, and the bonding interface tended to form a stable Cu/Ni/Cu6Sn5/Ni/Cu structure. Diffusion models were established and discussed to elucidate the mechanisms governing both stages.

The Impact of Zincation on the Electroless Nickel UBM for Low Cost Flip Chip Technology

Low-Temperature Ultrasonic Bonding of Cu/Sn Microbumps with Au Layer for High Density Interconnection Applications

Low Alkaline Solution to Deposit Electroless Ni-Zn-P Film on Al Pad

The effect of surface preparation on the nucleation of zinc-nickel alloy electroplated in acidic electrolyte on steel substrate

Effect of Zinc Immersion Pretreatment on the Electro-Deposition of Ni Onto AZ91D Magnesium Alloy

Regulating Zinc Nucleation Sites and Electric Field Distribution to Achieve High-Performance Zinc Metal Anode via Surface Texturing.

Wetting and Interfacial Chemistry of New Pb-Free Sn-Zn-Ag-Al-Li (SZAAL) Solder with Cu, Ni, and Al Substrates

Optimization of Bonding Methods for Controlling Sn Spillage in Fine Pitch Microbump Applications

A Cu/Ni/Cu/Sn1.8Ag Microbump Structure for Void-free Interface under Long Time High-Temperature Storage

Effect of Ag addition on the mechanical properties of Cu/Ni/Sn/Ni/Cu microbump with a sub-10 micron bump thickness

Zincophilic and Low-Active Metallic Particles-Induced Alloying/dealloying Behavior for High-Performance Aqueous Zinc Metal Batteries

Manipulating underpotential deposition nucleation of zinc deposition towards high-stable zinc metal battery

Au-SN Flip-Chip Solder Bump for Microelectronic and Optoelectronic Applications

Engineering Chemo-Mechanical Properties of Zn Surfaces via Alucone Coating

Impacts of Zinc Layer and Pouring Method on Interface Performance for Al-22Si/ZL104 Bi-Metal

Exploration of Pretreatment Process and Wettability of High Bonding Ni-P Coatings on W-Cu Composites for Electronic Packaging

Fabrication of Fine-Pitch Cu-Sn Microbumps Using Electroplating and Wet Seed Layer Etching

In-situ interfacial layer with ultrafine structure enabling zinc metal anodes at high areal capacity

The Research on a Low Cost Flip Chip Bumping Process by Stencil Printing

Effect of the Sn Addition on the Electrochemical Properties of Al/Pb Anodes and Its Application in Zinc Electrowinning

Grain modification and formation of tough IMC phase in submicron Sn–Ag microbumps via doping Zn and Ni in Cu substrate