Abstract:High-energy ball milling represents an efficient process for producing composite powders consisting of ceramic particles dispersed in a metallic matrix. However, collision events, plastic deformations, and cold welding during the milling lead to a flake or block-like shape of the resulting composite powders. Further consolidation of such irregularly shaped powders by powder bed-based additive manufacturing technologies can be challenging because of their low flowability and low bulk density. In this work, different approaches, including milling process parameters (speed, process control agent atmosphere) and post-treatments (mechanical and thermal), are investigated on their suitability to influence the particle shape, especially concerning the roundness of the composite powders consisting of the aluminum alloy AlSi10Mg with 5 vol% SiC and Al2O3 reinforcement. It is found that milling with menthol as a process control agent leads to the finest composite powder compared to other milling parameters, with the lowest particle roundness of 0.39 (initial powders 0.84). No success in rounding the milled composite powder could be achieved through mechanical post-treatment in a planetary ball mill. On the other side, the thermal spraying of, e.g., SiC reinforced AlSi10Mg powder resulted in a 77–82% relative roundness. A remarkable change in the microstructure and the shape of the composite powders could also be observed after heat treatment in tube furnaces at a temperature above the melting point of AlSi10Mg. The best result in terms of improved roundness (relative to around 85%) was obtained for Al2O3 reinforced at 600 °C. A further increase of the temperature to 700 °C resulted in a moderate coarsening of powders with Al2O3 and extensive sintering of powders with SiC, presumably due to a different distribution inside the matrix.

Preparing Al -Pb Alloy by Mechanical Milling and Canning Extrusion

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

High Strength Al–Al2O3p Composites: Optimization of Extrusion Parameters

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Formation of Nanoscale Metallic Glassy Particle Reinforced Al-Based Composite Powders by High-Energy Milling

Manufacturing and processing of aa3303 aluminum alloy by synthesis of elementary powders by powder metallurgy techniques of high energy ball milling and hot extrusion

Synthesis and characterisation of advanced ball-milled Al-Al2O3 nanocomposites for selective laser melting

Preparation of FeAl (B2) intermetallic powder by ball milling and heat treatment

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Mechanical alloying of FeAl intermetallic powder for metal injection moulding process

Effects of high-energy ball milling on structure and mechanical properties of L12 intermetallic compound Al67Mn8Ti25

Study of 6061-Al2o3p Composites Produced by Reciprocating Extrusion

Preparation of B4Cp/Al Composites via Selective Laser Melting and Their Tribological Properties

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

PREPARATION AND STRUCTURAL STUDY OF MECHANICAL ALLOYED OF Co50Fe20Cu2V8B20

Achieving ultra-high strength in Be/Al composites by self-exhaust pressure infiltration and hot extrusion process

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Study on Mechanical Properties and Microstructure of Cu20Fe80 Alloy Using the Mechanical Alloying