Abstract:In this study, the effects of different Cr content on the microstructure, impact properties, and wear resistance of Fe-Mn-B wear-resistant surfacing alloy layers were investigated using plasma powder surfacing technology. The results indicate that the addition of Cr does not alter the phase of the surfacing alloy layer. Cr is primarily found in solid solution within the primary phase, with a small amount in the eutectic structure. The primary phase transforms from (Mn,Fe) 2 B to (Mn,Fe,Cr) 2 B, and the eutectic structure shifts from small blocks to lamellar (Mn,Fe,Cr) 2 B + γ-Fe. The incorporation of Cr increases the impact energy of the surfacing alloy layer, with the highest impact energy of 44.8 J/cm 2 observed in the sample containing high Mn content and Cr. The fracture mode transitions from brittle fracture to a combination of brittle and ductile fracture. The addition of Cr promotes the precipitation of the primary crystal phase, enhancing its microhardness and consequently improving the macrohardness of the surfacing alloy layer. The macrohardness increases from 59.5 HRC in the low Mn content sample without Cr to 63.8 HRC in the high Mn content sample with 6.36 wt% Cr. The increased toughness and hardness of the primary phase, along with the transformation of the eutectic structure to lamellar, allow the primary phase to better resist abrasive particle indentation. As a result, the wear resistance of the surfacing alloy layer under two loads is significantly improved.

Research of the microstructure of the Co-Cr-W alloy plasma surfacing

Microstructure and Wear Characteristics of Cobalt-Based Alloy Deposited by Plasma Transferred Arc Weld Surfacing

Effects of Cr3 C2 on Microstructure and Wear Resistance of Cobalt-Base Alloy Coating Deposited by Plasma Transferred Arc Surfacing

Formation Mechanisms for (cr,co)7c3/(cr,co)23c6 Heterogeneous Precipitates and Stacking Faults Around Carbides in Surfacing Welding of Stellite Alloy on Stainless Steel

Investigation of the microstructure and friction mechanism of novel CoCrCu0.2FeMox high-entropy alloy coating using plasma arc cladding

Effect of different chromium contents on microstructure and two-body abrasive wear behavior of Fe-Mn-B surfacing alloys

Microstructure characterization of AlCoCrFeNiTi high-entropy alloy coating produced by atmospheric plasma spraying

Wear-resistance Performance of Spray-welding Coating by Plasma Weld-surfacing

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Study on the microstructure and wear resistance of AlCrCuFeNiTix high entropy alloys for surfacing welding

Microstructure and Wear Resistance of High Volume Fraction Carbide (cr, Fe)7C3 Reinforced Fe Based Coating

Research on Microstructure and Property of Fe-C-ΣX Multicomponent Alloy Plasma Arc Spray Welding

Synthesis and characterization of FeCoCrAlCu high-entropy alloy coating by laser surface alloying

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Microstructure and mechanical properties of CoCrFeMnNi/WC plasma deposited coating after the spark plasma sintering treatment

Investigated on the Nano-Y2O3/Co50 Composite Coatings by Plasma Transfer Arc Spray Welding

Microstructure and Dry Sliding Wear Behavior of Ultrafine-Grained Co-30 At% Cr Alloy at Room and Elevated Temperatures

Preparation of coatings containing Al-Cu-Cr quasicrystal and approximate phases by laser cladding

Influences of the Microstructure on the Wear Resistance of Cobalt-Based Alloy Coatings Obtained by Plasma Transferred Arc Process

Microstructure and properties of CrB2-Cr3C2 composite coatings prepared by plasma spraying

Microstructure and Its High Temperature Oxidation Behavior of W-Cr Alloys Prepared by Spark Plasma Sintering