Abstract:Optimization of process variables for laser cladding of Ni-based alloys was performed using the pre-placed powder method. The microstructure of laser clad, under optimal processing conditions, and furnace melted, under near equilibrium conditions, Ni-based alloys has been comparatively investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. Comparison of the microstructures of the laser-clad and furnace-melted alloys revealed a remarkable difference. The microstructure of the laser cladding is complex, composed of blocky CrB type chromium carbon borides, orthorhombic structured Cr7C3 type dendritic carbides, cellular-dendritic ν-Ni solid solution, different interdendritic eutectics and amorphous phases along grain boundaries. The interdendritic eutectics, either ν-Ni+M23C6 or ν-Ni+Ni3B (Ni2B), can form depending on the local composition. ν-Ni+Ni3B stable solidification and ν-Ni+Ni2B metastable solidification exist simultaneously because of the non-equilibrium rapid solidification involved during the laser cladding. In contrast, the microstructure of furnace-melted Ni-based alloy under near equilibrium solidification is composed of hexagonal structured Cr7C3 type carbides with hexagonal prism morphologies, near-equiaxed ν-Ni solid solution dispersed with fine Ni3Si precipitates, ν-Ni+Ni3B near lamellar eutectic and near-spherical Ni3B compound. ν-Ni is the main microstructural constituent in both the laser clad and furnace melted alloys. From the grain size, it was evident that the former is one to two orders finer than the latter.

Microscopic Morphology and Microstructure of Ti-N and Ti-Ni Phase Between the Dilution Zone and the Clad Zone in Laser Remelting Nicrbsi/Tin Layer on Ti-6al-4v Alloy Surface

Microscopic Morphology and Microstructure of Phases Between Dilution Zone and Clad Zone in Laser Remelting NiCrBSi/TiN Layer

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Study on Interface Microstructure and Laser Re-melting NiCrBSi+TiN Coating

Study on Microstructure of Laser Remelted NiCrBSi+TiN Coatings on Surface of Tianium Alloy

Study on Phase Transformation and Electrochemical Corrosion of TiNi Alloy Formed by Laser Solid Forming

Study On Tic/Ni Coating By Laser Alloying In-Situ Fabricated In The Internal Surface Of N80 Tubing

STRATIFICATION MECHANISM AND INTERFACE CHARACTERIZATION OF (tin), (tic)/nicrbsi COMPOSITE COATINGS SYNTHESIZED BY LASER REMELTING

Laser nitridation on Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy

Microstructure and Mechanical Properties of Laser Melting Deposited Ti_2Ni_3Si/NiTi Laves Alloys

Comparison of laser-clad and furnace-melted Ni-based alloy microstructures

In Situ Synthesis of Tin/Ti3al Intermetallic Matrix Composite Coatings on Ti6al4v Alloy

Intermetallic Alloys Ni<sub>3</sub>Si and Ni<sub>3</sub>(Si,Ti): Microstructures and Properties

Microstructure characterization and evolution mechanism of titanium during laser surface nitriding

Laser Cladding of Ti-6Al-4V Alloy with TiC and TiC+NiCrBSi Powders

AMORPHOUS/NANOCRYSTALLIZATION OF TiN-TiB2 REINFORCED LASER CLAD COMPOSITES

Microstructure Evolution in Laser Solid Forming of Ti–50wt% Ni Alloy

Microstructure and Corrosion Behavior of Ti-Nb Coatings on NiTi Substrate Fabricated by Laser Cladding

In Situ Synthesis of Titanium Nickel Intermetallic Compounds Layer and TiN Coating by Laser Cladding

Microstructure and Mechanical Properties of Ti-6Al-4V Prepared by Nickel Preplating and Electron Beam Surface Remelting

Surface nitridation of titanium using pulse laser gas alloying method and its microstructure analysis with XRD and SEM