Abstract:Indentation creep testing and uniaxial creep testing were carried out in this paper in order to set up the relationship between them. The aim of this work is to present a experimental validated method to determine the material creep parameters (nm, creep stress exponent; cm, creep factor, ε˙=cmσnm, ε˙, tensile creep strain rate at the steady state; σ, creep stress, usually from the uniaxial tensile testing) from the indentation creep testing. Aluminum alloy 2A12 was tested in this paper. Firstly, a set of indentation creep testing was carried out at 200°C with a flat cylindrical indenter. The net indentation creep stresses were between 905.4 and 1414.8MPa. The steady indentation creep rates in different indentation stresses were obtained, from which the indention creep parameters (d˙=cIσNnI, d˙, the indentation creep depth rate at the steady state; σN, the net section stress; nI, indentation stress exponent; cI, indentation factor) can be derived. The indentation creep testing was simulated by the finite element method. In order to validate the method, a set of uniaxial tensile creep testing was carried out at the same temperature, i.e. 200°C. From the uniaxial tensile creep results, the material creep parameters (ε˙=cmσnm) were also derived. It is shown that the stress exponent determined from indentation and uniaxial creep testing is same, respectively, at a same temperature. A method has been presented to set up the relationship between the indentation creep parameters (d˙=cIσNnI) and uniaxial creep parameters (ε˙=cmσnm) based on a conversion factor. With the indentation creep testing results in conjunction with finite element creep analysis, the material creep parameters (nmI-FEM and cmI-FEM) have also been derived. It can be concluded that the indentation creep testing can been used to determine the creep parameters (nm and cm). The most important conclusion is that the indentation creep exponent is equal to the material creep exponent, nm=nI.

EFFECT OF LOADING RATE ON NANOINDENTATION CREEP PROPERTIES OF Al FILMS

The mechanisms of nanoindentation creep in Al thin metal films

EFFECT OF GRAIN SIZE AND HOLDING LOAD ON NANOINDENTATION CREEP OF Cu FILM

Strain Rate Sensitivity of Nanoindentation Creep in Polycrystalline Al Film on Silicon Substrate

An Investigation of Nanoindentation Creep in Polycrystalline Cu Thin Film

Effects of loading rate and peak load on nanoindentation creep behavior of DD407Ni-base single crystal superalloy

Effect of Loading Rate on Creep Behavior and Shear Transformation Zone in Amorphous Alloy Thin Films, and Its Correlation with Deformation Mode Transition

Effect of Loading Rate on the Creep Behaviour of Epoxy Resin Insulators by Nanoindentation

The Effects of Annealing on Creep Behavior of Copper Film During Nanoindentation

Experimental and numerical study of the method to determine the creep parameters from the indentation creep testing

Nanoindentation Creep Behavior of an Al0.3CoCrFeNi High-Entropy Alloy

Effect of Strain Rate on Deformation Behavior of AlCoCrFeNi High-Entropy Alloy by Nanoindentation

Indentation size and loading strain rate dependent creep deformation of nanocrystalline Mo

Indentation Size Dependent Plastic Deformation of Nanocrystalline and Ultrafine Grain Cu Films at Nanoscale

Nanoindentation Creep Behavior of an Al 0.3 CoCrFeNi High-Entropy Alloy

EXPERIMENTAL AND NUMERICAL STUDY ON INDENTATION CREEP WITH A FLAT INDENTER

Nanoindentation creep testing: Advantages and limitations of the constant contact pressure method

Effects of Loading Strain Rate and Stacking Fault Energy on Nanoindentation Creep Behaviors of Nanocrystalline Cu, Ni-20 Wt.%fe and Ni

THE SIMULATION OF CREEP INDENTATION TESTING

Rate-dependent nanoindentation creep behavior of a Fe-based amorphous coating

Indenter Load Effects on Creep Deformation Behavior for Ti-10V-2Fe-3Al Alloy at Room Temperature