Pulse-Cycle Skip Modulation in Switching Converter

罗萍,李肇基,熊富贵,陈光(礻禹)

2004-01-01

Abstract:This paper proposes a modulation mode named Pulse-cycle Skip Modulation (PSM) in switching converter and analyzes its principle and characteristics. The state equations, modulation factor, response speed and the efficiency of PSM are also described. Compared with (PWM) control mode, PSM is a better control method in switching converter.

What problem does this paper attempt to address?

PWM/PSM Dual-Mode Controller for High Efficiency DC-DC Buck Converter

Yidie Ye,Jianping Qiu,Lingling Dong,Lenian He

DOI: https://doi.org/10.1109/appeec.2010.5448331

2010-01-01

Abstract:This paper introduces a novel method of realizing PWM/PSM dual-mode controller for high efficiency DC-DC buck converters. A minimum duty cycle control module is added to the PWM control loop, and with a simple logic control, the system can work in PSM mode when the load is light to improve the efficiency of the system over wide load range. A testing chip of the dual-mode DC-DC buck converter is implemented by CSMC's 0.5 mu m 40 V BCD process. The testing results proved the system functioned well in both PWM mode and PSM mode, and switched smoothly between the two modes. The efficiency is greatly improved when the load is light. It is no less than 75% over the whole load range and can reach 91% with heavy load.
High voltage PWM/PSM dual-mode asynchronous BUCK converter

朱丽芳,何乐年,叶益迭

DOI: https://doi.org/10.3785/j.issn.1008-973X.2011.01.032

2011-01-01

Abstract:A BUCK converter with high input/output voltage and low power consumption, consisting of two working modes of pulse width modulation (PWM) and pulse skipping modulation (PSM), was proposed in order to obtain high conversion efficiency in the whole load range. The converter automatically skips from PWM to PSM mode by detecting the duty cycle of switch pulse. The input voltage of the converter ranges from 3 V to 24 V, and the output voltage ranges from 2.5 V to (VI-0.5) V. The converter works in PWM-mode at a switching frequency of 1 MHz when the load current is large, and operates in PSM-mode with a reduced switching frequency if the load current is low, which makes a high efficiency in the whole load current range. The PWM/PSM dual-mode converter switches from PWM to PSM mode by limiting the minimum duty cycle, and the mode control circuit was easily realized by some logic gate and one-shot circuit. The chip was implemented by using the CSMC 0.5 μm 40 V mixed-signal process. Experimental results indicate that the efficiency is still higher than 55% when the output voltage is 5 V, even when the input voltage is 24 V which is the highest input voltage of this chip. The chip can smoothly alter mode and display good load regulation.
Design and Implementation of High-Efficiency and Low-Power DC-DC Converter with PWM/PFM Modes

Jing Wang,Wenchao Gong,Lenian He

DOI: https://doi.org/10.1109/icasic.2007.4415701

2008-01-01

Abstract:A high-efficiency low-power multimode DC-DC converter with pulse-width modulation (PWM) and pulse-frequency modulation (PFM) is proposed. This converter works in PWM mode on heavy load condition. In order to improve efficiency, it switches to PFM mode on light load condition. With suitable control and mode switch method, both simulation and chip test results indicate that the converter performs seamless switching between PWM and PFM modes. The total output voltage error, including line and load regulation, is less than plusmn2%, the maximum quiescent current is less than 15 muA, the maximum of efficiency reaches 92.6%. Simulated and implemented in CSMC 0.5 mum CMOS process.
Design and implementation of off-line switching power-supply controller

苑婷,何乐年,柯徐刚

DOI: https://doi.org/10.3785/j.issn.1008973x.2010.11.015

2010-01-01

Abstract:A design method of an off-line switching power-supply controller with properties of high-efficiency and low-power is presented to improve performances of off-line power supplies. The controller was designed on basis of pulse-width modulation (PWM) mode and pulse skipping modulation (PSM) mode. The design method of the controller loop is based on the peak current mode. The controller operates in PWM mode, when the feedback voltage is less than 4.75 V, and works in PSM mode otherwise, ensuring high efficiency. Additional functions, such as short-circuit protection, over-voltage protection, under-voltage lockout, internal slope compensation, leading-edge blanking on current sense are included. For reducing the electromagnetic interference (EMI), the switching frequency is designed to be randomized within the range of 1 kHz at around centre frequency to flatten the power spectral density (PSD). The chip was implemented by using TSMC's 0.6 μm 40 V high voltage BCD process. Simulation results indicate that the controller realizes the required working modes and performs seamless switching between the modes. The controller can be applied to Li-Ion battery charger with a wide range of AC input (85~264 V) or power adapter.
Multi-mode Control Strategy for Primary-Side Regulation System

Kan Liu,Kexu Sun,Jianxiong Xi,Lenian He

DOI: https://doi.org/10.1109/icsict.2016.7998736

2016-01-01

Abstract:A multi-mode control strategy for primary-side regulation (PSR) system is presented. The idea uses four mode control strategy to improve the efficiency under variety load conditions. In addition, the usual peak current control mode is replaced by voltage control mode under standby condition. By this way, the pulse width of drive signal can be reduced regardless of the leading edge blanking time in the peak current control mode when the power switch turns on. Thus the standby power can be reduced when the system switching frequency remains the same as conventional system. The prototype is achieved by using CSMC 700V BCD technology. The experiment results show that the average efficiency is improved about 3.6% comparing with conventional system and the standby power is less than 10mW under different conditions.
Modeling and Analysis of PWM Converters with a New GSSA Method

Liang Dong,Hao Ma,Fei Xu

DOI: https://doi.org/10.1109/iecon.2008.4758059

2008-01-01

Abstract:Due to the switching operation, the pulse-width modulation (PWM) converters are inherent time-variant systems with comprehensive dynamics. The generalized state-space averaging (GSSA) method is an approach to model them as time-invariant systems, defined by a set of differential equations and capable of representing circuit waveforms. This paper proposes a new generalized state-space averaging model to model the converters with variations in input voltage, which can give accurate ripple estimations and also helps for the control design without complicated calculation. The model can be treated as a basic modeling framework of some specific converters, such as the power factor correctors (PFC). As examples, the models of buck and boost circuits are analyzed and simulation results are presented.
Improved PWM Modulation Strategy for CHB Multilevel Converter

董璧韬,胡长生,姚文熙,张飞力,张军明,徐德鸿

DOI: https://doi.org/10.13234/j.issn.2095-2805.2023.1.55

2023-01-01

Abstract:The cascaded H-bridge（CHB） multilevel converter is the most widely used topology in a medium-voltage high-power motor drive system, and the traditional level-shifting pulse width modulation（LS-PWM） and phase-shifting pulse width modulation（PS-PWM） strategies cannot strike a balance between the input and output current harmonics. In this paper,the input and output THD of the CHB multilevel converter under these two modulation strategies are compared, and the reasons for the difference between the input and output waveforms obtained using these two methods are analyzed. Then,a partly carrier PS-PWM modulation method is proposed. By combining the advantages of these two modulation methods,this method not only keeps the characteristics of module power balance and low harmonic of grid-side input current in the PS-PWM modulation, but also realizes a satisfying output power quality in the LS-PWM modulation. An experimental platform of three-phase seven-level CHB converter was built, and the proposed partly carrier PS-PWM strategy was verified.
Research on Flux Linkage Locus Control with Minimum Switching Losses

林平,胡长生,刘晨阳,张仲超

DOI: https://doi.org/10.3969/j.issn.1000-100x.2001.03.007

2001-01-01

Abstract:This paper presents the principle of PWM based on flux linkage locus control. For reducing switching losses, three kind of modulation methods are analyzed by adjusting the duty time of the zero vectors and the duty order of every vector. The phase voltage waveforms also indicate that the switching losses can be extremely reduced by choosing proper modulation method. A prototype based on the theories is designed. Experiment shows these schemes are available and simple.
Dynamic Modeling for a Bi-directional DC/DC Converter with Two Regulative Parameters

SUN Li-ping,XU De-hong,CHEN Min

2006-01-01

Abstract:PWM plus phase-shift (PPS) technique is a technique combining PWM control technique and phase-shift (PS) control technique. The PPS controlled bi-directional DC/DC converters have two regulative parameters, i.e., phase-shift angleφand duty cycle D. A new technique modeling for PPS controlled full bridge bi-directional DC/DC converters is proposed, and the validity of this technique has been verified by simulation.
Reduced Switching-Frequency Modulation and Circulating Current Suppression for Modular Multilevel Converters

Qingrui Tu,Zheng Xu,Lie Xu

DOI: https://doi.org/10.1109/tpwrd.2011.2115258

IF: 4.825

2011-01-01

IEEE Transactions on Power Delivery

Abstract:This paper describes a modified phase-shifted carrier-based pulsewidth-modulation (PSC-PWM) scheme for modular multilevel converters (MMC). In order to reduce the average device switching frequency, a reduced switching-frequency (RSF) voltage balancing algorithm is developed. This paper also proposes a circulating current suppressing controller (CCSC) to minimize the inner circulating current in an MMC. Based on the double line-frequency, negative-sequence rotational frame, the three-phase alternative circulating currents are decomposed into two dc components and are minimized by a pair of proportional integral controllers. Simulation results based on a detailed PSCAD/EMTDC model prove the effectiveness of the modified PSC-PWM method and the RSF voltage-balancing algorithm. The proposed CCSC not only eliminates the inner circulating current but also improves the quality of the converter ac output voltage. A simple loss evaluation demonstrates that the RSF voltage-balancing algorithm and the CCSC reduce the converter power losses.
Optimal Design and Control of 5kw PWM Plus Phase-Shift (PPS) Control Bidirectional Dc-Dc Converter

L Shi,LP Sun,DH Xu,M Chen

DOI: https://doi.org/10.1109/apec.2006.1620522

2006-01-01

Abstract:The paper proposed optimal design and control of a 5kW PPS control bidirectional dc-dc converter. In this paper, we will propose the losses model based on different kinds of semiconductor switches: MOSFET or IGBT and different input voltage: 42V or 380V. Based on the loss model, we are able to design the PPS control bidirectional dc-dc converter with minimized switch losses. The dynamic model of the converter will be designed to design the feedback control system. A new control strategy is proposed, which is based on the dynamic model.
Comparison Of Three Pwm Strategies - Spwm,Svpwm & One-Cycle Control

B Hua,Zm Zhao,S Meng,Jz Liu,Xy Sun

DOI: https://doi.org/10.1109/PEDS.2003.1283169

2003-01-01

Abstract:Sinusoidal Pulse Width Modulation (SPWM) and Space Vector Pulse Width Modulation (SVPWM) are the most popular modulation strategies applied to variable frequency and adjusting speed systems, and there are diverges in comparing the merits and demerits of their own. Also there is another modulation strategy called One-cycle Control. This paper gathers the three strategies and does some comparisons through simulation based on a simulation tool-PSIM, and has drawn some profitable conclusions.
An Improved Modulation Technique with Minimum Switching Actions within One PWM cycle for Open-End Winding PMSM System with Isolated DC BUS

Wei Hu,Chenhui Ruan,Heng Nian,Dan Sun

DOI: https://doi.org/10.1109/TIE.2019.2920618

IF: 7.7

2020-01-01

IEEE Transactions on Industrial Electronics

Abstract:Due to the application of dual inverters in the structure of open-end winding permanent-magnet synchronous machine system with isolated dc bus, the double number of switching devices are employed and thus the switching actions within one pulsewidth modulation (PWM) period are relatively high. To reduce the switching actions, an improved modulation technique is proposed in this letter. In the proposed technique, the reference voltages in the synchronous coordinate system are transferred to the three-phase stationary frame through Park transformation and thus the duration time corresponding to the three-phase windings can be directly obtained. On this basis, by synchronously adjusting the duration time of three phases, the maximum one can be adjusted to be the control period while their resultant voltage remains constant. Furthermore, the switching actions are assigned to the switching devices based on the polarity of duration time for each phase, with the principle of keeping the switching device on one side clamped. The novelty of the proposed technique is that it can be universally applied to minimize the number of switching actions within one PWM cycle for any kind of voltage ratio of the system without sector identification. The experimental validation of the proposed scheme is given to validate its effectiveness.
Switching Characterization and Power Loss Optimization for Modular Multiactive Bridge Converter under Common Phase Shift Control

Haoyu Wang,Shiqi Ji,Di Mou,Liqiang Yuan,Yangbin Zeng,Zhengming Zhao

DOI: https://doi.org/10.1109/jestpe.2023.3279658

IF: 5.462

2023-01-01

IEEE Journal of Emerging and Selected Topics in Power Electronics

Abstract:In modular multiactive bridge (MMAB) converters, which are inherently coupled among dc ports, single phase shift (SPS) control has been widely adopted due to its simplicity in implementation and neglect of coupling characteristics in control algorithms. However, under SPS control, the converter may have unfavorable system efficiency performance, especially when voltage conversion ratios of ports mismatch. To improve the efficiency, this article proposes a common phase shift (CPS) control method for a generalized MMAB or multiactive bridge (MAB) converter. A comprehensive operation analysis of MMAB converters under CPS control with switching characterization of power semiconductors has been carried out. Besides, an overall power loss model is derived, with main electrical components and their power-loss behaviors taken into consideration. Moreover, an optimal strategy aimed at power loss optimization is proposed to improve the efficiency of the converter. Finally, a four-port experimental MMAB converter prototype has been constructed. The experimental results and tested efficiency curves have verified the feasibility and effectiveness of the proposed CPS control.
An Improved Near-State Pulse-Width Modulation with Low Switching Loss for a Permanent Magnet Synchronous Machine Drive System

Pei Qing,Ruoyu Chen,Qiang Gao

DOI: https://doi.org/10.3390/en17133157

IF: 3.2

2024-06-27

Energies

Abstract:Common-mode voltage (CMV) leads to the shaft voltage and shaft current by coupling the capacitor network in the permanent magnet synchronous machine (PMSM), which affects the reliability of the whole motor drive system. Based on the low-CMV modulation strategy for the PMSM drive system, this paper proposed an improved near-state pulse-width modulation (NSPWM) on switching loss. First, the generation mechanism for the switching signals of NSPWM was analyzed, and it was observed that there exists one phase of switches in an inactive state for every sector. Then, to reduce the switching loss of the NSPWM, this paper proposed an improved NSPWM modulation strategy based on power factor angle to adjust switching action, which ensures the switching tubes that have the biggest conduction current have no switching action. In addition, the switching loss analytic formula of the NSPWM was derived to prove the correctness of the proposed method for optimizing switching loss. Finally, the proposed modulation strategy was carried out in the simulation and experimental platform. Under the premise of good steady and dynamic performance, the results show that the proposed modulation strategy has less switching loss.

energy & fuels
Multi-mode control strategy in three-level DC-DC converter for higher efficiency operation under light-load and standby conditions

Lu Liu,Wenxi Yao,Zhengyu Lu

DOI: https://doi.org/10.1109/APEC.2015.7104459

2015-01-01

Abstract:A multi-mode control strategy (MMCS) is proposed to improve the efficiency of three-level (3L) DC-DC converter under light-load and standby conditions without auxiliary components. 3L converter is typically controlled in phase-shift control mode (PSCM) in order to achieve zero-voltage-switching (ZVS) to reduce switching loss with rated load. However, since little energy is provided to discharge the parasitic capacitors of the switches, light load leads to hard switching and makes efficiency drop in PSCM. The proposed control strategy aims to overcome this problem. It consists of three modes: PSCM to reduce switching loss with heavy load, pulse-width-modulated control mode (PWMCM) to reduce conduction loss with light load and PWM burst control mode (PWMBCM) to further reduce unnecessary loss under standby condition. A 120V, 1.5kW prototype has been made to validate this control strategy. The efficiency of the 3L converter is increased by up to 24.7 percentage points under standby condition and 3.7 percentage points with light load.
A Novel PWM Model for Cascaded H-bridge Converters

GAO Zhigang,LI Yongdong

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2010.27.015

2010-01-01

Abstract:This paper analyzed the essence of switch pulses and introduced a group of variables named pulse net area(PNA).Based upon the research on the PNA,the pulse width modulation(PWM) model for cascaded H-bridge converters was established.This model can be used to evaluate and optimize PWM methods.Three improved PWM methods were introduced.Experiment results proved the correctness and feasibility of the PWM model applied to the further research on the modulation method for cascaded H-bridge converters.It is practical to use the proposed model in establishing new modulation methods,reducing switching cost,and assessing the characteristics of certain modulation method for cascaded H-bridge converters.
Switching State Sequences-Based Modulation Scheme for T-Type 5L-ANPC Converter.

Kun Wang,Yingfei Xu,Guangdi Li,Yan Deng,Xiangning He,Yi Lu,Yong Yang

DOI: https://doi.org/10.1109/access.2019.2930974

IF: 3.9

2019-01-01

IEEE Access

Abstract:A switching state sequences (SSSs)-based modulation scheme along with a dead-time effect compensation method is proposed in this paper. In the proposed modulation scheme, the converter's switching states changing sequence in one carrier period, i.e., the SSS, is treated as the basic unit to control the T-type 5L-ANPC converter. Because there are only two possible voltage levels in each SSS, the converter can be controlled as a traditional two-level converter within each SSS. Thus, a switching pulse modification-based method is proposed to compensate the dead-time effect within each SSS. Moreover, an SSS transition rule and the transition diagram are furtherly presented to avoid the dead-time effect between different SSSs. Consequently, both the output voltage delay and the unwanted voltage glitches that caused by the dead-time effect are avoided in the whole modulation range. Besides, a balancing strategy is proposed to balance the flying capacitor voltage based on the charging abilities of SSSs. The performance and effectiveness of the proposed modulation scheme are validated by both simulation and experimental results.
A Sub-harmonic Oscillation Elimination Method with PI Modulation in PSR Flyback Converter

Xinyu Wei,Chong Wang,Daying Sun,Wenhua Gu

DOI: https://doi.org/10.1109/ecce53617.2023.10362212

2023-01-01

Abstract:To increase the power density and satisfy the higher power requirements, primary-side regulation (PSR) flyback converter working in continuous conduction modulation (CCM) mode is often used. However, with peak current control, the magnetizing inductor current will diverge from the stable value when the duty ratio is larger than 0.5, resulting in sub-harmonic oscillation and unstable system. In this article, a sub-harmonic oscillation elimination method with PI modulation is proposed. The stable control parameters of PI modulation are specially designed to eliminate sub-harmonic oscillation. And the stability of PSR flyback converter in CCM mode is analyzed from the eigenvalues and eigenvectors of the discrete iterative matrix, which describes the iterative relationship of the control and output variable perturbations. Slope compensation or current sensing with ADC device is not required, which greatly simplifies the control. The stability analysis and designed control parameters are experimentally verified on an field programmable gate array (FPGA) controlled 20-V/3-A PSR flyback prototype with CCM mode. Experiments prove that sub-harmonic oscillation is eliminated with the parameter-designed PI control method.
New Modulation Strategies for Hybrid Cascaded Multilevel Converter

XUE YingLin,XU Zheng,TANG Geng,ZHENG Xiang,LIU Zhengfu

DOI: https://doi.org/10.3969/j.issn.1000-1026.2012.22.020

2012-01-01

Abstract:Modulation strategies of the hybrid cascaded multilevel converter(HCMC) under different modes are studied.Firstly,to reduce switching frequency and losses of director switches,a novel asymmetrical square wave modulation at fundamental switching frequency is proposed.Under this modulation,the energy exchange characteristic between the wave shaping circuit and the outside system is analyzed,and then the range of the voltage modulation ratio and duty ratio under steady operation is derived.Secondly,a modified phase-shifted carrier-based pulse width modulation(PWM) with sub-module capacitor voltage balancing strategy is developed for the wave shaping circuits.Moreover,the direct current blocking mode and static synchronous compensator mode are also investigated,and it is pointed out that the modulation strategy under steady operation mode can be effective under the latter mode by amending the modulation reference voltage.At last,the effectiveness and feasibility of modulation strategies is verified by PSCAD/EMTDC simulation.

Pulse-Cycle Skip Modulation in Switching Converter

PWM/PSM Dual-Mode Controller for High Efficiency DC-DC Buck Converter

High voltage PWM/PSM dual-mode asynchronous BUCK converter

Design and Implementation of High-Efficiency and Low-Power DC-DC Converter with PWM/PFM Modes

Design and implementation of off-line switching power-supply controller

Multi-mode Control Strategy for Primary-Side Regulation System

Modeling and Analysis of PWM Converters with a New GSSA Method

Improved PWM Modulation Strategy for CHB Multilevel Converter

Research on Flux Linkage Locus Control with Minimum Switching Losses

Dynamic Modeling for a Bi-directional DC/DC Converter with Two Regulative Parameters

Reduced Switching-Frequency Modulation and Circulating Current Suppression for Modular Multilevel Converters

Optimal Design and Control of 5kw PWM Plus Phase-Shift (PPS) Control Bidirectional Dc-Dc Converter

Comparison Of Three Pwm Strategies - Spwm,Svpwm & One-Cycle Control

An Improved Modulation Technique with Minimum Switching Actions within One PWM cycle for Open-End Winding PMSM System with Isolated DC BUS

Switching Characterization and Power Loss Optimization for Modular Multiactive Bridge Converter under Common Phase Shift Control

An Improved Near-State Pulse-Width Modulation with Low Switching Loss for a Permanent Magnet Synchronous Machine Drive System

Multi-mode control strategy in three-level DC-DC converter for higher efficiency operation under light-load and standby conditions

A Novel PWM Model for Cascaded H-bridge Converters

Switching State Sequences-Based Modulation Scheme for T-Type 5L-ANPC Converter.

A Sub-harmonic Oscillation Elimination Method with PI Modulation in PSR Flyback Converter

New Modulation Strategies for Hybrid Cascaded Multilevel Converter