Abstract:High repetition rate femtosecond laser micro-processing has been applied to ophthalmological hydrogel polymers and ocular tissues to create novel refractive and diffractive structures. Through the optimization of laser irradiation conditions and material properties, this technology has become feasible for future industrial applications and clinical practices. A femtosecond laser micro-processing workstation has been designed and developed. Different experimental parameters of the workstation such as laser pulse duration, focusing lens, and translational stages have been described and discussed. Diffractive gratings and three-dimensional waveguides have been fabricated and characterized in hydrogel polymers, and refractive index modifications as large as + 0.06 have been observed within the laser-irradiated region. Raman spectroscopic studies have shown that our femtosecond laser micro-processing induces significant thermal accumulation, resulting in a densification of the polymer network and increasing the localized refractive index of polymers within the laser irradiated region. Different kinds of dye chromophores have been doped in hydrogel polymers to enhance the two-photon absorption during femtosecond laser micro-processing. As the result, laser scanning speed can be greatly increased while the large refractive index modifications remain. Femtosecond laser wavelength and pulse energy as well as water and dye concentration of the hydrogels are optimized. Lightly fixed ocular tissues such as corneas and lenses have been micro-processed by focused femtosecond laser pulses, and refractive index modifications without any tissue-breakdown are observed within the stromal layer of the corneas and the cortex of the lenses. Living corneas are doped with Sodium Fluorescein to increase the two-photon absorption during the laser micro-processing, and laser scanning speed can be greatly increased while inducing large refractive index modifications. No evidence of cell death has been observed in or around the laser-induced refractive index modification regions. These results support the notion that femtosecond laser micro-processing method may be an excellent means of altering the refraction or higher order aberration content of corneal tissue without cell death and short-term tissue damage, and has been named as Intra-tissue Refractive Index Shaping (IRIS). The femtosecond laser micro-processing workstation has also been employed for laser transfection of single defined cells. Some preliminary results suggest that this method can be used to trace individual cells and record their biological and morphological evolution, which is quite promising in many biomedical applications especially in immunology science. In conclusion, high repetition rate femtosecond laser micro-processing has been employed to fabricate microstructures in ophthalmological hydrogels and ocular tissues. Its unique three-dimensional capability over transparent materials and biological media makes it a powerful tool and will greatly impact the future of…

Micrograting Polymerization Fabrication with a Single Femtosecond Laser Pulse at 400 Nm Wavelength

Two-Photon Polymerization of Gratings by Interference of A Femtosecond Laser Pulse

The Fabrication of Permanent Holographic Gratings in Bulk Polymer Medium by a Femtosecond Laser

Unidirectional Lasing from A Spiral-Shaped Microcavity of Dye-Doped Polymers

Toward On-Chip Unidirectional and Single-Mode Polymer Microlaser

Nanofabrication of Bulk Diffraction Nanogratings via Direct Ultrashort-Pulse Laser Micro-Inscription in Elastomers and Heat-Shrinkable Polymers

Fabrication of High Refractive Index-Modulation Structures in Fused Silica by Femtosecond Laser Pulses

Polymer Gratings with Low Surface Relief Based on Photopolymerization-Induced Internal Diffusion

LASER DIRECT WRITING OF LONG PERIOD FIBER GRATING BY 800 NM FEMTOSECOND LASER PULSES

Fabrication Of Nano-Grating Inside Transparent Materials By Using A Single Femtosecond Laser Beam

Dammann gratings as integratable micro-optical elements created by laser micronanofabrication via two-photon photopolymerization.

Photofabrication of Periodic Microstructures in Azodye-Doped Polymers by Interference of Laser Beams

Fabrication of Large Grating by Monitoring the Latent Fringe Pattern

Long-period fiber grating fabrication by high-intensity femtosecond pulses at 211 nm

Single-Mode Lasing in Polymer Circular Gratings

Photoinduced Permanent Gratings Inside Bulk Azodye-Doped Polymers By The Coherent Field Of A Femtosecond Laser

Photonic Crystal Structures with Submicrometer Spatial Resolution Achieved by High-Power Femtosecond Laser-Induced Photopolymerization

Micro-processing of Polymers and Biological Materials Using High Repetition Rate Femtosecond Laser Pulses

Fabrication of beam shapers in the bulk of fused silica by femtosecond laser pulses.

Fabrication of broadband, high-efficiency, metal-multilayer-dielectric gratings

Efficient frequency doubling of 1.5 μm femtosecond laser pulses in quasi-phase-matched optical fibers