Abstract:The Al63Cu25Fe9Cr3 quasicrystalline was prepared by conventional casting method. The microstructures and phase composition of Al63Cu25Fe12 quasi-crystalline and Al65Cu20Fe10Cr5 phases were characterized by XRD and SEM. Aluminium based composites was fabricated by using the Al63Cu25Fe9Cr3 quasicrystalline particles as the reinforcing phase and ZL101 as matrix with mechanical stirring. The effects of quasicrystals content, on the microstructure and mechanical properties of the obtained composite, were investigated. The results show that the as-cast quasicrystalline material is composed of d-phase(Al65Cu20Fe10Cr5), I-phase(Al63Cu25Fe12), lambda-Al3Fe, beta-AlFe3 and a small amount of eta-AlCu, theta-Al2Cu phases. After heat treatment, the quasicrystalline intermediate alloy composition tends to quasicrystal phase. In the composite material, the diffusion between the quasicrystalline and the matrix alloy caused the decomposition of the structure of quasicrystalline phase. With the increase of quasicrystalline content, the tensile strength of the composites increases. However, addition of the Cr element changes the acicular beta-Fe(Al80-85Fe6-9Si10-15) phase into a manlike or bone-like alpha-Fe(Al80-85Fe4-8Si6-8Cr3-5) phase which increases the elongation of the composite. The best comprehensive mechanical properties corresponded to the 7 wt% quasicrystalline particles. Strengthening mechanism of quasicrystal reinforced aluminum matrix composites, a model that model considers the dislocation strengthening mechanism and the effect of load transfers mechanism on the tensile strength of composites. This theory calculates the tensile strength of quasicrystalline reinforced aluminum matrix composites and verifies the effectiveness of the model through experiments.

Quasicrystals in as-cast Al-Ni-Fe alloys

Decagonal Quasicrystalline Phase in As-Cast and Mechanically Alloyed Al–Cu–Cr Alloys

Characterization of Aluminium Matrix Compositesreinforced by Al–Cu–Fe-Cr Quasicrystalline Particles

Solidification Character of Al_(72)Ni_(12)Co_(16) Single-Decagonal Quasicrystal Alloy

Near-equiatomic high-entropy decagonal quasicrystal in Al 20 Si 20 Mn 20 Fe 20 Ga 20

Microstructure and mechanical properties of an aluminum alloy reinforced by Al–Ni–Co–Mn quasi-crystalline

Microstructures and phase transformation of Al-based composite materials reinforced by Al-Cu-Co decagonal quasicrystalline particles

Insight into the Microstructure and Micromechanical Behavior and Mechanism of the Constitutional Phase of FeNiCrAl0.63 Multi-Principal Element Alloy

Dynamic solidification model of low-density FeCrNiAl multi-component alloy

Precipitation of Nano-Scale Icosahedral Quasicrystalline Phase in Hf-Al-Ni-Cu Metallic Glass Promoted by Addition of Ti

Phase transition and mechanical properties of al-based composites reinforced by Al72Ni12Co16 decagonal quasicrystalline particles

Crystalline phases found in rapidly quenched Ni-Nb-Zr alloys

Formation of AlCuFe icosahedral quasicrystal by mechanical alloying: XAFS and XRD studies

Interfacial Reaction Between Al 72 Ni 12 Co 16 Decagonal Quasicrystalline Particles and Liquid Aluminium

Icosahedral Quasicrystal Layer Observed on Λ Phase in Al-Cu-Fe Alloy

Nucleation and growth of quasicrystal-related precipitates within the Al-matrix of AlEr(Fe) alloys

Al-Cu-Fe alloys: the relationship between the quasicrystal and its melt

Effect of Co, Cr and Ni on Phase Equilibrium of Fe3al Intermetallics

Influence of particle content on the microstructures and properties of Al-11Mg-based composites reinforced by quasicrystal particles

Quasicrystalline Al-Fe Phase Formed by Ion Mixing

Microstructure and Mechanical Properties of Al-base Composites by Addition of Al–Ni–Co Decagonal Quasicrystalline Particles Through a Mechanical Stirring Route