Abstract:Al2O3-Cr2O3 refractories have excellent slag corrosion resistance and can adapt to the oxidation/reduction atmosphere in the smelting reduction ironmaking furnace. However, Al2O3-Cr2O3 refractories have poor mechanical properties and sintering properties. In order to improve the mechanical properties of Al2O3-Cr2O3 materials, the CaAl12O19 reinforced Al2O3-Cr2O3 composites were prepared by pressureless sintering process, and the influences of CaO content on the sintering properties, mechanical properties, and microstructure evolution of the composites were studied. The results show that a small amount of CaO can significantly improve the compactness of the composites, which is mainly due to the formed sheet-like CA6 fill the gap between the solid solutions, and reduces the porosity of the composites. In addition, the sheet-like CA6 makes the connection between solid solutions closer, and the intergranular fracture gradually transforms into a mixed mode of intergranular and transgranular fracture. The best mechanical propertie is observed at S4 with the CaO content of 2 wt.%. Compared with sample S0 without CaO, the hardness, compressive strength and flexural strength of the S4 were increased by 35.19 %, 49.69 %, and 68.34 %, respectively. The addition of excessive CaO will deteriorate the mechanical properties of the composites, because the formation of a large number of layered CA6 increases the porosity of the composites. Furthermore, a small amount of CaO addition can significantly improve the thermal shock resistance of the composites. After 10 and 20 thermal shock cycles, the strength loss rates of S4 are only 5.83 % and 8.74 %, respectively.

Erosion behavior between CaCl2 and β-Sialon -SiC composite used for blast furnaces

Erosion behavior between CaCl2 and beta-sialon-SiC composite used for blast furnaces

Erosion Behavior of C/SiC Composites in Atomic Oxygen

Oxidation behavior and ablation mechanism of Cf/ZrB2-SiC composite fabricated by vibration-assisted slurry impregnation combined with low-temperature hot pressing

Hot strength and microstructure of β-sialon-Al2O3-SiC composites

Effect of SiC Content on the Ablation and Oxidation Behavior of ZrB2-Based Ultra High Temperature Ceramic Composites

Ablation behavior of C/C–Zr1-xHfxC-SiC composites under an oxyacetylene flame at above 2500 °C

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Multi-cycle and long-term ablation behavior of Cf/ZrB2-SiC composites at 2500 °C

Ablation behavior and mechanisms of 3D Cf/ZrB2-SiC composite applied in long-term temperature up to 2400 °C

Alkali Resistance Mechanism of Al2O3 SiC Refractory Castable

High-temperature corrosion of a Si3N4/W composite exposed to molten MgCl2-NaCl-KCl salts

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Microstructure and mechanical properties of CaAl12O19 reinforced Al2O3-Cr2O3 composites

Ablation behavior and mechanisms of Cf/(Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C–SiC high-entropy ceramic matrix composites

HOT STRENGTH AND MICROSTRCTURE OF Βsialonal_2o_3sic COMPOSITES

Structural characteristics and ablative behavior of C/C–ZrC–SiC composites reinforced with “Z-pins like” Zr–Si–B–C multiphase ceramic rods

Long-term ablation behavior and mechanisms of 2D-Cf/ZrB2-SiC composites at temperatures up to 2400 °C

Comparison of the ablation resistance of mullite modified C/C-SiC-HfC and C/C-SiC-HfC composites under oxyacetylene flame of 2.38 MW/m 2 heat flux

Ablation behavior of C f /ZrC–SiC ultra–high temperature ceramic composites in oxyacetylene torch and plasma wind tunnel

High Temperature Oxidation and Microstructural Evolution of SiC Layer of TRISO Particles in the Presence of NaCl