Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Surface Modification of Poly(dimethylsiloxane)-fabricated Microfluidic Chip by UV Radiation

Chemical Modification on Top of Nanotopography to Enhance Surface Properties of PDMS

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Surface Modification Of Poly(Dimethylsiloxane) Microfluidic Chips By Treatment In An Oxygen Atmosphere

Surface modification of poly(dimethylsiloxane) microfluidic devices by ultraviolet polymer grafting.

PDMS Surface Modification Parameters Based on UVO Irradiation

Surface Modification and Bonding of Poly(dimethylsiloxane) by Oxygen Plasma Treatment under Medium Vacuum

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

Solution-phase Surface Modification in Intact Poly(dimethylsiloxane) Microfluidic Channels.

Surface Modification Of Pdms In Microfluidic Devices

Method for fabrication of paper-based microfluidic devices by alkylsilane self-assembling and UV/O3-patterning.

Surface modification of PDMS microfluidic devices by controlled sulfuric acid treatment and the application in chip electrophoresis

One-stage Fabrication of Sub-Micron Hydrophilic Microchannels on PDMS

Ultraviolet Sealing and Poly(dimethylacrylamide) Modification for Poly(dimethylsiloxane)/glass Microchips

Fabrication of 1-d nanochannels on PMMA substrate by photoresist-free uv lithography and UV-assisted bonding under low temperature

Selective Modification for Polydimethylsiloxane Chip by Micro-Plasma

An Improved Surface Modification of Poly(dimethylsiloxane) Via a Green Chemistry Approach for On-Chip Biomolecular Separation

Surface Modification of Poly(dimethylsiloxane) and Its Applications in Microfluidics-Based Biological Analysis

A Simple and Low-Cost Method for Fabrication of Polydimethylsiloxane Microfludic Chips.

Fabrication of PDMS Microfluidic Chip Used in Ultraviolet Integrated Biological Chip

Novel Fabrication Technology Of Polydimethylsiloxane Microfluidic Chip