Abstract:The precipitation behavior and the microstructural evolution of a dual-phase Cu-15 wt%Ag alloy during annealing were investigated. We discussed the effects of dislocation density, grain size, solute atom concentration, and precipitation morphology on strength and electrical conductivity. The results showed that continuous precipitation and discontinuous precipitation simultaneously occurred during the annealing of the Cu-15 wt%Ag alloy. It was accompanied by pronounced recovery and recrystallization, significantly decreasing the strength and electrical resistivity of the cold-rolled Cu-15 wt%Ag alloy. After 48 h of annealing at 350 °C, the fully recrystallized Cu-15 wt%Ag alloy exhibited a higher strength (299 MPa) and a lower electrical resistivity (1.92 μΩ cm) compared to the samples annealed at higher temperatures. The higher strength was attributed to smaller grain size and higher volume fraction of the continuous precipitation zone. Nanoscale Ag precipitates formed by continuous precipitation provided more extensive precipitation strengthening than sub-micrometer Ag precipitates formed by discontinuous precipitation. In addition, reducing the dislocation density and the concentration of solid atoms by controlling the annealing conditions was an effective strategy to weaken the dislocation scattering and impurity scattering effect in the Cu-15 wt%Ag alloy. The electrical resistivity of the fully crystallized Cu-15 wt%Ag alloy was linearly correlated to the concentration of Ag solute atoms. The electrical resistivity of the annealed Cu-15 wt%Ag alloy increased by 0.117 μΩ cm when 1 at.% Ag was dissolved in the Cu solid solution.

Effect Of Diffusion Annealing On Microstructure And Composition Distribution In Interfacial Regions Of Silver-Copper Bimetallic Sheets

Diffusion annealing of copper–silver bimetallic strips at different temperatures

Microstructure and elemental distribution of multicrystal Ag/Cu interface in bimetallic strips with diffusion treatment

A Study on Annealing Treatment Under Various Temperatures for the Interfaces of Cu-Ag Composite Sheets

Effect of the Diffusion Annealing on Concentration Distributions in interfacial Regions of Au/Ag-Cu/Cu-Ni-Zn Laminate Strips

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Effect of annealing processes on microstructure, mechanical properties and conductivity of Cu-12%Ag alloy composite-reinforced by fibers

Behaviors of the Interface and Matrix for the Ag/Cu Bimetallic Laminates Prepared by Roll Bonding and Diffusion Annealing

Effects of pre-annealing process on microstructure and properties of the Cu-12%Ag composite wire

Annealing effects on the microstructure, strength, and electrical resistivity in a dual-phase Cu-15 wt%Ag alloy

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Effect of Annealing Temperature on the Interfacial Microstructure and Bonding Strength of Cu/Al Clad Sheets with a Stainless Steel Interlayer

Interface Structure Between Ag Precipitates and Cu Matrix and Its Effect on the Properties of the Cu-Ag Alloy

Effect of annealing temperature on microstructure and tensile properties of copper/aluminum composite thin strip

Effect of Annealing Temperature on Peeling Strength of Ag/Cu Bimetallic Strips

Effect of Roll Bonding and Diffusion Treatment Temperature on Bond Properties of Ag/Cu Bimetallic Laminates

A Study on the Microstructural Evolution, Interfacial Diffusion and Mechanical Properties of Ultra-thin Stainless Steel–Copper Composites Fabricated by Roll Bonding

Effect Of Intermediate Annealing On The Interface And Plasticity Of Cu-Ni-Si/Al-Mg-Si Clad Composite Wires

Influence Of Soldering Temperature And Dwelling Time On Morphological Evolution Of Cu6sn5 Intermetallic Compound At The Sn-3.0ag-0.5cu/Cu Interface

Effects of asymmetry and annealing on interfacial microstructure and mechanical properties of Cu/Al laminated composite fabricated by asymmetrical roll bonding

Effects of Annealing Temperature on Texture in Cu-12%Ag Double-Phase Filamentary Composite