Abstract:Decarburization is an unwanted carbon-loss phenomenon on the surfaces of a material when they are exposed to oxidizing environments at elevated temperatures. Decarburization of steels after heat treatment has been widely studied and reported. However, up to now, there has not been any systematic study on the decarburization of additively manufactured parts. Wire-arc additive manufacturing (WAAM) is an efficient additive manufacturing process for producing large engineering parts. As the parts produced by WAAM are usually large in size, the use of a vacuum environment to prevent decarburization is not always feasible. Therefore, there is a need to study the decarburization of WAAM-produced parts, especially after the heat treatment processes. This study investigated the decarburization of a WAAM-produced ER70S-6 steel using both the as-printed material and samples heat-treated at different temperatures (800 °C, 850 °C, 900 °C, and 950 °C) for different durations (30 min, 60 min, and 90 min). Furthermore, numerical simulation was carried out using Thermo-Calc computational software to predict the carbon concentration profiles of the steel during the heat treatment processes. Decarburization was found to occur not only in the heat-treated samples but also on the surfaces of the as-printed parts (despite the use of Ar for shielding). The decarburization depth was found to increase with an increase in heat treatment temperature or duration. The part heat-treated at the lowest temperature of 800 °C for merely 30 min was observed to have a large decarburization depth of about 200 μm. For the same heating duration of 30 min, an increase in temperature of 150 °C to 950 °C increased the decarburization depth drastically by 150% to 500 μm. This study serves well to demonstrate the need for further study to control or minimize decarburization for the purpose of ensuring the quality and reliability of additively manufactured engineering components.

EXPERIMENTAL RESEARCH ON BEHAVIOR OF DECARBURIZATION FOR THE FLAT DIE STEELS AISI D2，M2 AND S5

Experimental and modelling research on the influence of different pre-decarburization microstructures of Fe-0.6C-1.8Si-0.8Mn spring steel

Surface Decarburization Behaviour of A Novel Die Steel

Influence of heating process on decarburization behavior of metallurgical saw blade with 65Mn steel

The Numerical Simulation of Decarburization of 60Si2CrVA in Heat Treatment by DEFORM-3D and the Research of Practical Application

Study on Decarburization Mechanism and Law of GCr15 Bearing Steel during Heat Treatment

Experimental Study on Vacuum Carburizing Process for Low-Carbon Alloy Steel

Study on Heat Treatment Process of Rolling Die

Decarburization of Wire-Arc Additively Manufactured ER70S-6 Steel

Thermal deformation behavior and microstructure evolution of Fe−8.5Mn−1.5Al light−weight medium manganese steel

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Effects of deep cryogenic treatment on the microstructure evolution, mechanical and thermal fatigue properties of H13 hot work die steel

Simulation and Experimental Verification of Die Quenching Deformation of Aviation Carburized Face Gear

Optimizing the Morphology of Primary Carbides and Mechanical Properties during Processing Of Cast-Steel (Din Gx210crv12 1) Press-Forming Dies

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

Experimental Study on Thermodynamic Performance of Boron Steel B1500HS Used for Hot Stamping Process

Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels

Effect of heat treatment on microstructure and mechanical properties of directed energy deposition-Arc 300 M steel

Achieving high hardness and wear resistance in phase transition reinforced DC53 die steel by laser additive manufacturing

The Tribological Properties Of Ion Sulfurized Die-Steel Under Dry Sliding Condition