Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Temperature on Tribological Performances of Molybdenum Dialkyldithiocarbamate

The Thermal Stability and Lubricity of Zinc Thiomolybdenate at Temperatures Up to 500°C

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of MoDTC and MoDTP on Tribological Behavior of Cylinder Liner/Piston Ring

Effects of annealing treatment on tribological behavior of tungsten-doped diamond-like carbon film under lubrication (Part 2): Tribological behavior under MoDTC lubrication

Impacts of Molybdenum Dithiocarbamate (modtc) Friction Modifier on Tribological Performance of Fully-Formulated GF-3 Engine Oil

Influence of Oxidative Degradation of Lubricant and Anti-Friction Modifier on Tribological Behavior of Cylinder Liner/Piston Ring

Effect of Frictional Pair Materials on Tribological Behavior of Molybdenum Dithiocarbomate As an Additive

Effect of MoS 2 element diffusion under high temperature condition on the tribological properties of cemented carbide materials

Tribochemical interactions of piston ring coatings with molybdenum dithiocarbomate friction modifier

Influence of Mo doping on the tribological behavior of Ti3AlC2 ceramic at different temperatures

Investigation of the elevated temperature tribological property and wear mechanism of Fe‐15Cu‐0.8C materials containing Mo‐coated MoS2 powders

Performance of MoS2/Zr Composite Coatings at Different Deposition Temperatures

Importance of the catalytic effect of the substrate in the functionality of lubricant additives: the case of MoDTC

Study on Atmospheric Tribology Performance of MoS2–W Films with Self-Adaption to Temperature

Effect of Temperature on the Friction and Wear Behavior of Electroless Ni–P–MoS2–CaF2 Self-Lubricating Composite Coatings

Effect of Molybdenum Contents on Microstructure and High-Temperature Wear Behavior of SiMo Ductile Iron

Friction and wear behavior of molybdenum-disulfide doped hydrogen-free diamond-like carbon films sliding against Al2O3 balls at elevated temperature

Tribological interactions between TiN PVD coating and MoDTC under boundary lubrication conditions

High-Temperature Friction and Wear Behavior of Nickel-Alloy Matrix Composites with the Addition of Molybdate

Novel Anti-Wear Performance of Nano Magnesium Silicate Hydroxide in Boundary Lubrication Under High Temperature