Abstract:The Al63Cu25Fe9Cr3 quasicrystalline was prepared by conventional casting method. The microstructures and phase composition of Al63Cu25Fe12 quasi-crystalline and Al65Cu20Fe10Cr5 phases were characterized by XRD and SEM. Aluminium based composites was fabricated by using the Al63Cu25Fe9Cr3 quasicrystalline particles as the reinforcing phase and ZL101 as matrix with mechanical stirring. The effects of quasicrystals content, on the microstructure and mechanical properties of the obtained composite, were investigated. The results show that the as-cast quasicrystalline material is composed of d-phase(Al65Cu20Fe10Cr5), I-phase(Al63Cu25Fe12), lambda-Al3Fe, beta-AlFe3 and a small amount of eta-AlCu, theta-Al2Cu phases. After heat treatment, the quasicrystalline intermediate alloy composition tends to quasicrystal phase. In the composite material, the diffusion between the quasicrystalline and the matrix alloy caused the decomposition of the structure of quasicrystalline phase. With the increase of quasicrystalline content, the tensile strength of the composites increases. However, addition of the Cr element changes the acicular beta-Fe(Al80-85Fe6-9Si10-15) phase into a manlike or bone-like alpha-Fe(Al80-85Fe4-8Si6-8Cr3-5) phase which increases the elongation of the composite. The best comprehensive mechanical properties corresponded to the 7 wt% quasicrystalline particles. Strengthening mechanism of quasicrystal reinforced aluminum matrix composites, a model that model considers the dislocation strengthening mechanism and the effect of load transfers mechanism on the tensile strength of composites. This theory calculates the tensile strength of quasicrystalline reinforced aluminum matrix composites and verifies the effectiveness of the model through experiments.

Microstructure analysis of Al-Cu-Cr phases in Al65Cu20Cr15 quasicrystalline particles/Al base composites

Characterization of Aluminium Matrix Compositesreinforced by Al–Cu–Fe-Cr Quasicrystalline Particles

Microstructure and phase components of the as-cast Cu-0.4%Cr-0.12%Zr-0.01%Si

Microstructure and Mechanical Behavior of Quaternary Eutectic α+θ+Q+Si Clusters in As-Cast Al-Mg-Si-Cu Alloys

Transmission Electron-Microscopy Study of Small-Angle Grain-Boundaries, Dislocations and Modulated Phases in Al-Li-Cu Quasi-Crystals

Incommensurate Modulated Structure in the Icosahedral Quasicrystalline Phase T2 of an Al-Li-Cu Alloy

Formation of AlCuFe icosahedral quasicrystal by mechanical alloying: XAFS and XRD studies

Microstructure and mechanical properties of an aluminum alloy reinforced by Al–Ni–Co–Mn quasi-crystalline

Interfacial reaction kinetics of (Al63Cu25Fe12) 99Ce1 quasicrystal reinforced 6061 aluminum matrix composites

Scratch-induced surface microstructures on the deformed surface of Al-Cu-Fe icosahedral quasicrystals

Preparation and Characterization of Al11cr4 Phase by Diffusion of Al/Cr Composite Film

Quasicrystalline phases in AlCuCo alloy

Phase-Transformation from Quasi-Crystal to Crystal

Transmission electron microscopy study of defects in AlLiCu quasicrystals

Defects In The Quasicrystalline Phase Of Al-Li-Cu

Unveiling the Fine Microstructure of Nanoscale Composite Particles Embedded in Brittle Si Phase in an Al-Si-Cu-Mg Alloy

Analysis of phases in a Cu–Cr–Zr alloy

Phase Transformation Between Multiply-Twined Crystal Aggregates and Decagonal Quasicrystal in an Al-Pd-Mn Alloy

Simulated structure and thermodynamics of decagonal Al-Co-Cu quasicrystals

Studying the Effects of Doping Minor Transition Metal Elements in Al-Cu-Fe-Mn Quasicrystals on the Structure and Phase Change of Quasicrystals

Electron microscopy study of scratch-induced surface microstructures in an Al-Cu-Fe icosahedral quasicrystal