Abstract:The alloying of Nb₅Si₃ modifies its properties. Actual compositions of (Nb,TM)₅X₃ silicides in developmental alloys, where X = Al + B + Ge + Si + Sn and TM is a transition and/or refractory metal, were used to calculate the composition weighted differences in electronegativity (Δχ) and an average valence electron concentration (VEC) and the solubility range of X to study the alloying and properties of the silicide. The calculations gave 4.11 < VEC < 4.45, 0.103 < Δχ < 0.415 and 33.6 < X < 41.6 at.%. In the silicide in Nb-24Ti-18Si-5Al-5Cr alloys with single addition of 5 at.% B, Ge, Hf, Mo, Sn and Ta, the solubility range of X decreased compared with the unalloyed Nb₅Si₃ or exceeded 40.5 at.% when B was with Hf or Mo or Sn and the Δχ decreased with increasing X. The Ge concentration increased with increasing Ti and the Hf concentration increased and decreased with increasing Ti or Nb respectively. The B and Sn concentrations respectively decreased and increased with increasing Ti and also depended on other additions in the silicide. The concentration of Sn was related to VEC and the concentrations of B and Ge were related to Δχ. The alloying of Nb₅Si₃ was demonstrated in Δχ versus VEC maps. Effects of alloying on the coefficient of thermal expansion (CTE) anisotropy, Young's modulus, hardness and creep data were discussed. Compared with the hardness of binary Nb₅Si₃ (1360 HV), the hardness increased in silicides with Ge and dropped below 1360 HV when Al, B and Sn were present without Ge. The Al effect on hardness depended on other elements substituting Si. Sn reduced the hardness. Ti or Hf reduced the hardness more than Cr in Nb₅Si₃ without Ge. The (Nb,Hf)₅(Si,Al)₃ had the lowest hardness. VEC differentiated the effects of additions on the hardness of Nb₅Si₃ alloyed with Ge. Deterioration of the creep of alloyed Nb₅Si₃ was accompanied by decrease of VEC and increase or decrease of Δχ depending on alloying addition(s).

Stoichiometric and off-stoichiometric alloying in ti5si3 by nb or cr addition

Stoichiometric and Off-Stoichiometric Alloying in Silicide Compound Ti5Si3 by Nb or Cr Additions

Effects of Alloying on the Microstructures and Mechanical Property of Nb-Mo-Si Based in Situ Composites

Alloying Effect on the Stability of Ti5Si3 from First‐Principles Study

Microstructure and Mechanical Properties of Refractory High Entropy (mo0.5nbhf0.5zrti)bcc/m5si3 In-Situ Compound

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Formation Mechanism of Tisi Phase and Silicide Kinds on Microstructure and Mechanical Properties for Ti-5al-5mo-5cr-3nb-2zr Alloyed by Silicon

High Temperature X-Ray Diffraction Study of the Effect of Nb and Si on Oxidation Behavior of Ti3Al Alloy

Microstructure Characteristics and Mechanical Properties of Hf0.5Mo0.5NbTiZr Refractory High Entropy Alloy with Cr Addition

On the Alloying and Properties of Tetragonal Nb5Si3 in Nb-Silicide Based Alloys

Effects of Si variation and Zr addition on the microstructure, oxidation resistance and mechanical property at 1523 K of Nb-Si-Ti/Zr/Hf-Cr/Al high-entropy superalloys

Synergistic Effect of Zr and Ti on Microstructure and Properties for Nb Si Based In-Situ Composites

Microstructure and Fracture Toughness of Nb-Si Based Alloys by with Ti, Zr and Hf Additions

Synergistic Effects of Fe and C on Microstructure and Properties of Nb-Ti-Si Based Alloys

Microstructural and High Temperature Deformation Characterization of Ti–45Al–3Nb–(Cr, Mn, Mo, Sc) Alloy

The influence of Si alloying on the crept microstructure and property of a TiAl alloy prepared by powder metallurgy

On the Microstructure and Properties of Nb-18Si-6Mo-5Al-5Cr-2.5W-1Hf Nb-Silicide Based Alloys with Ge, Sn and Ti Additions (at.%)

Microstructure Evolution and Tensile Properties of Conventional Cast TiAl-based Alloy with Trace Ni Addition

Calculation and Analysis of Mixing Entropy of CoCrFeNiTix Alloys

Microstructures and Properties of Nb–Si-based Alloys with B Addition

Effects of Titanium Addition on Microstructure and Mechanical Properties of CrFeNiTix (x = 0.2–0.6) Compositionally Complex Alloys