Abstract:Fiber-reinforced polymer (FRP) has superior mechanical properties such as lightweight, high specific strength, and high specific rigidity. Recent important issues of manufacturing FRP are cost reduction and high cycle manufacturing of high-quality products. It is expected that in-situ process monitoring using a smart sensor can be used to solve the issues. Therefore, we paid attention to the monitoring method using an optical fiber sensor because it has good accuracy and embeddability. Up to the present, we have been developing a degree-of-cure (DOC) monitoring method for large and complex-shaped FRP products by Fresnel’s reflection optical fiber sensor. This sensor was based on Fresnel’s reflection due to the mismatch of refractive-index between glass and resin. In the previous study, the effect was investigated that the optical bending loss on the DOC measurement using a φ125 μm optical fiber sensor. It was confirmed that a φ125 μm optical fiber was sometimes broken at less than a 2 mm bending radius as one of the results of previous study. However, it is needed that stable measurement of DOC at very severe embedding condition if we want more expansion of the application range of FRP in the future. Thus, we aim to develop a DOC measurement system that can be measured by severe bending conditions using φ80 μm optical fiber in this study. The optical loss property was measured by winding the fiber around the jig whose radiuses were 1, 1.5, 2, 3, 4, and 5 mm. From the result, the φ80 μm optical fiber sensor didn’t break if it was bent less than 2 mm bending radiuses. Besides, it was found that the optical loss rate dL/dx was increased with the decrement of the bending radius R, and Ln R and Ln dL/dx have a linear relationship. The DOC of epoxy resin was measured by using the φ80 μm optical fiber sensor. The DOC curves were calculated from the measured refractive-index curves. From the result, it was confirmed that the DOC curve of the φ80 μm optical fiber sensor agreed very well with the simulation curve by the Kamal model. Therefore, it can be estimated that appropriate the measurement result of DOC by the φ80 μm optical fiber sensor.

Investigation on the fiber sensor for real-time monitoring the curing process of composite material through measuring the speckle spatial spectrum (SSS) of fiber

An Investigation of a Fiber Optic Sensor in the Composite Cure Process

Study of composite cure real time sensing using fiber optic sensor

Fiber-optic Composite Cure Sensor: Monitoring the Curing Process of Composite Material Based on Intensity Modulation

Investigation Of Multifunctional Fiber Optic Sensor In Smart Composite

Magnetic Fiber Enabled Curing Electrogram: Real-time Process Monitoring for Thermosetting Polymer Materials

Spatially Modulated Fiber Speckle for High-Sensitivity Refractive Index Sensing.

Real-time cure monitoring of smart composite materials using extrinsic Fabry-Perot interferometer and fiber Bragg grating sensors

Experimental Study of Monitoring and Controlling of Composite Cure Process in Autoclave Featured with Fiber Optic Sensor

Simultaneous measurement of strain and temperature during and after cure of unsymmetric composite laminate using fiber-optic sensors

Real time monitoring of the curing degree and the manufacturing process of fiber reinforced composites with a carbon nanotube buckypaper sensor

Monitoring of Curing Process of Epoxy Resin by Long-Period Fiber Gratings

Cure monitoring of epoxy resin via use of FBG

Real-time self-monitoring and smart bend recognizing of fiber-reinforced polymer composites enabled by embedded magnetic fibers

Recent Progress in Distributed Fiber Optic Sensors

A Novel Multifunctional Optical Fiber Sensor Based on Fbg and Fiber Optic Coupler

DEVELOPMENT OF DEGREE-OF-CURE MEASUREMENT METHOD BY THIN-DIAMETER FRESNEL’S REFLECTION OPTICAL FIBER SENSOR

In-situ monitoring of carbon fiber/epoxy composite with FBG sensors under curing and thermal cycling conditions

A single three-parameter tilted fibre Bragg grating sensor to monitor the thermosetting composite curing process

Fiber-Optic Point-Based Sensor Using Specklegram Measurement

Investigation on Sensitivity Enhancement for Optical Fiber Speckle Sensors.