Abstract:This study focuses on the effects of a hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt.%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. SEM and EDS were used to characterize the hybrid composite made of Al-Cu-Mg alloy. Optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nano-reinforcements within the matrix. EDS analysis revealed SiC and PSSA reinforcement in the matrix. The mechanical properties (tensile, flexural, and impact strength) and wear properties of the composites and alloy were evaluated according to the ASTM standards. The hybrid reinforced composites displayed remarkable results compared with the base alloy. Among all composites, the 2:2 wt.% SIC and PSSA hybrid reinforced composite exhibited a significant enhancement in both tensile strength and flexural strength, with a 29.15% increase in tensile strength and a 27.64% increase in flexural strength. However, the inclusion of these reinforcements led to a declined in ductility and impact strength of the Al-Cu-Mg alloy composite. Maximum reductions in ductility and impact strength were observed in the 0:4 wt.% SiC and PSSA-reinforced composites, with decreases of 47.67% and 3.56%, respectively. For the 2:2 wt.% SiC and PSSA composites, these reductions were 23.64% and 3.16%, respectively. The SEM analysis of the fractured surfaces of the composites tested for the mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying coefficients of friction.

EFFECTS OF CATEGORY AND CONTENT OF REINFORCEMENTS ON MECHANICAL PROPERTIES OF METAL MATRIX COMPOSITES

Mechanical Behavior of Deformable Particles Reinforced Al Matrix Composites

Effects of Reinforcement Shape and Distribution on Mechanical Properties of AI Based Composites

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

EFFECT OF THE ADDITION OF REINFORCEMENTS ON DAMPING CAPACITY OF PURE MAGNESIUM

Strengthening mechanism of load sharing of particulate reinforcements in a metal matrix composite

The effect of reinforcement particles weight percentage on the mechanical properties and plastic flow behaviour of aluminum alloy 7075 matrix material

Experimental Studies on Machinability of 14 Wt.% of Sic Particle Reinforced Aluminium Alloy Composites

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB2 co-reinforced Al-Zn-Mg-Cu composites

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB 2 co-reinforced Al-Zn-Mg-Cu composites

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Effect of Reinforcement on the Tribological Behavior of CuFe-Based Composites

Effects of Reinforcement Shape and Distribution on Mechanical Cycle Performance in Al Composites

Effects of Mg Content on Microstructure and Mechanical Properties of SiCp/Al-Mg Composites Fabricated by Semi-Solid Stirring Technique

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Effect of the amount of SiC particles on the microstructure, mechanical and wear properties of FeMnCoCr high entropy alloy composites

The Fabrication and Properties of Particle Reinforced Cast Metal Matrix Composites