Abstract:The morphology development of in situ reactive blends is compared with their nonreactive counterparts. The specific mechanical energy required to process these blends under different processing conditions is examined. The various rheological states that the blends undergo during the processing are visualized. This paper discusses the evolution of morphology in 80/20 (vol/vol) (polypropylene‐maleic anhydride)/polypropylene (PP)/(polystyrene‐oxazoline)/polystyrene (PS) reactive blends and nonreactive 80/20 PP/PS blends. For both the blends, the PS forms the continuous phase initially, traps the PP‐maleic anhydride or PP pellets within, and gradually deforms these pellets to lamellar sheets and elongated fibers. Eventually, the irregular domains of PP coalesce and invert to form the continuous phase in a transition known as the "processing phase inversion." The nonreactive PP/PS blend needed much higher torque to be deformed from pellets to a viscoelastic melt than their reactive counterparts. Despite the significant differences in their processing energy, the reactive and nonreactive blends have similar morphologies during the inversion process. The changes in the structure of the blends were captured on video by a custom‐built visualization system and correlated with scanning electron microscopy of the fractured surfaces, along with monitoring the changes in the torque levels during the processing. The solid‐state properties of the minor phase were crucial for deforming the major phase pellets and, consequentially, the work required to process the blends. Due to a suppression of coalescence due to the presence of in situ formed copolymers at the interface of the PP/PS, a finer dispersion was obtained in the case of the reactive blend systems. Highlights Visualization of polymer melt blending. In situ reaction during processing. Processing energy requirements during blending.

THE EVOLUTION OF MORPHOLOGY ON BLENDING OF POLYSTYRENE/POLY(cis-BUTADIENE)

Phase Morphology of Immiscible Polymer Blends of Polystyrene with Poly(cis-butadiene) Rubber by Rayleigh Scattering

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Effect of Phase Morphology on the Reactive Blending

Rheological Properties and Morphological Evolutions of Polypropylene/Ethylene-Butene Copolymer Blends

Morphology development of polymer blends with different viscosity ratios along an extruder

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Morphology Study of Immiscible Polymer Blends in A Vane Extruder

Effect of morphology on the interfacial slip of immiscible polypropylene/polystyrene blends

Morphology and Deformation Mechanisms of Polystyrene Low-Density Polyethylene Blends Studied by Tem

Effect of Mixer Resident Time on the Overall Moduli of Polymer Blends

Morphology and Rheology of PP/POE Blends in High Shear Stress Field

Molecular Dynamics of Different Polymer Blends Containing Poly(2,6-Dimethyl-1,4-phenylene Ether).

Comparing the morphological evolution of reactive and nonreactive Polystyrene/Polypropylene polymer blends: Processing phase inversion

Morphology Development in Multi-Component Polymer Blends: I Composition Effect on Phase Morphology in PP/PET Polymer Blends

Phase Behavior and its Viscoelastic Responses of Poly(methyl methacrylate) and Poly(styrene-co-maleic anhydride) Blend Systems

Dynamic Rheological Behavior and Morphology Near Phase-Separated Region for a LCST-type of Binary Polymer Blends

Analysis of the Multistep Solidification Process in Polymer Blends

MECHANICAL PROPERTIES AND MORPHOLOGY OF POLYPROPYLENE/POLYSTYRENE BLENDS*

Studies on Phase-Separation in Polyblends of Block Copolymers