Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

Comparing the morphological evolution of reactive and nonreactive Polystyrene/Polypropylene polymer blends: Processing phase inversion

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Effect of Mixing Protocol on Compatibilized Polymer Blend Morphology

Visualization of Poly(ether Imide) and Polycarbonate Blending in an Internal Mixer

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

Morphological analysis of mechanically recycled blends of high density polyethylene and polypropylene with strong difference in melt flow index

Phase morphology of nascent impact polypropylene copolymer and its evolution in the melt

Concept of Reactive Compatibilizer-Tracer for Discovering Interfacial Reaction and Morphology Development for In-Situ Compatibilizing Blending Processes

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Controls of Gradient Morphology and Surface Properties of Polymer Blends

Two Antagonistic Effects of Flow/mixing on Reactive Polymer Blending

Rheological Properties and Morphological Evolutions of Polypropylene/Ethylene-Butene Copolymer Blends

Inversion of Phase Morphology in Polymer-Blend Thin Films on Glass Substrates

Rheological Behavior and Nonisothermal Crystallization of Polypropylene/Epoxidized Natural Rubber Blends

Understanding the Morphological Changes in the Polypropylene/Polyamide 6 Fifty/Fifty Blends by Interfacial Modifiers Based on Grafted Atactic Polypropylenes: Microscopic, Mechanical, and Thermal Characterization

Impact of thermomechanical reprocessing on multilayer plastic packaging blend

Study on the formation rate of gradient phase morphology in the polymer blends

Analysis of phase morphology and dynamics of immiscible PP/PA1010 blends and its partial-miscible blends during melt mixing from SEM patterns

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend