Abstract:Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300−425 K are obtained. The TEG (7-pair) and TEC (127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared to the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.

Experimental Studies on Overall Property of Thermoelectric Modules with Sandwiched Structures

Realizing ultrahigh ZT value and efficiency of the Bi2Te3 thermoelectric module by periodic heating

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Analytical and Experimental Studies on an Innovative Composite Approach for Enhanced Thermoelectric Performance

Performance evolution of thermoelectric modules under constant heat flux

Fabrication And Evaluation Of Microscale Thermoelectric Modules Of Bi2te3-Based Alloys

Numerical Modeling of the Performance of Thermoelectric Module with Polydimethylsiloxane Encapsulation

Fabrication and evaluation of microscale thermoelectric modules of Bi<sub>2</sub>Te<sub>3</sub>-based alloys

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

Device‐Level Optimization of n‐Type Mg3(Sb, Bi)2‐Based Thermoelectric Modules toward Applications: A Perspective

High Performance Dual-mode Module for Power Generation and Cooling Based on Optimized BiSbTe

Understanding the Asymmetrical Thermoelectric Performance for Discovering Promising Thermoelectric Materials

Designing Cost-Performance Porous Thermoelectric Materials by Interface Engineering Through Atomic Layer Deposition

Enhanced Energy Harvesting from Thermoelectric Modules: Strategic Manipulation of Element Quantity and Geometry for Optimized Power Output

Fabrication and Performance Simulation of Microscale Thermoelectric Modules Made with Bi2Te3-Based Alloys

Bismuth Telluride/Half‐Heusler Segmented Thermoelectric Unicouple Modules Provide 12% Conversion Efficiency

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

High Efficiency Bi2te3-Based Materials and Devices for Thermoelectric Power Generation Between 100 and 300 Degrees C

Study of Thermal Insulation Materials Influence on the Performance of Thermoelectric Generators by Creating a Significant Effective Temperature Difference

Advances in bismuth-telluride-based thermoelectric devices: progress and challenges

Output and mechanical performance of thermoelectric generator under transient heat loads