Abstract:Polyurethane foam (PUF) is one of the most well-known cellular materials and is widely employed in various industrial and biomedical fields thanks to its many advantages. These include mechanical and material characteristics such as low density and thermal conductivity, and high specific elastic modulus and strength. Despite of these advantages, the PUF has extremely complex material nonlinearity, with changes in density and strain rate, which is a major obstacle to material design and the application of PUF-based structures. PUF has elasto-viscoplastic behavior including three stages of material features, linear elasticity, softening/plateau with stress drop and densification. These phenomena depend strongly on strain rate and density. Therefore, in this study, a phenomenological constitutive model, namely, an elasto-viscoplastic model, was proposed to describe the density- and strain rate-dependent material nonlinear behavior of PUF. The yield surface-independent plastic multiplier, and the hardening- and softening-associated internal state variables proposed by Frank and Brockman, and Zairi et al. were adopted in the constitutive model, respectively. The proposed constitutive model was discretized using the implicit time integration algorithm and was implemented into a user-defined subroutine of the commercial finite element analysis program, ABAQUS. At the same time, a deterministic identification method for material parameters of the constitutive model was introduced to predict the precise material response of PUF under arbitrary densities and strain rates. To do this, the three-dimensional constitutive model was contracted to a one-dimensional equation, and the explicit equation for each material parameter was derived. Then, the strain hardening- and softeningdependent material parameters were calculated using experimental results, such as the work hardening ratestress curve and the yield stress-strain rate curve. After analyzing the obtained material parameters, it was found that the material parameters were strongly dependent on the density and the strain rate. Consequently, the macroscopic material response of PUF, such as a uniaxial compressive stress-strain curve, can be predicted based on the proposed method in this study.

Rate-Dependent Constitutive Model Coupled with Temperature Softening for Open-Cell Aluminum Foam

Mechanical Properties and Constitutive Model Applied to the High-Speed Impact of Aluminum Foam That Considers Its Meso-Structural Parameters.

Study on Correlation Between Parameters of "single Factor" Constitutive Model and Temperature for 7050 Aviation Aluminum-Alloy

A RATE-DEPENDENT CONSTITUTIVE MODEL FOR ALUMINUM FOAMS AND ITS APPLICATION TO THE ENERGY ABSORPTION OF LIGHTWEIGHT SANDWICH PANELS WITH ALUMINUM FOAM CORES

High temperature and mesostructure effect on aluminum foam compression responses

Dynamic and Static Compression Tests and FEA Analyses of Aluminum Foam Specimen with Variable Density in the Loading Direction

Study on Dynamic Impact Response and Optimal Constitutive Model of Al-Mg-Si Aluminum Alloy

Experimental and Physical-Based Constitutive Model Study of Fcc Metal over Wide Temperature and Strain Rate Ranges

THE MECHANICAL BEHAVIORS OF CLOSED-CELL ALUMINUM-ALLOY FOAMS WITH SPHERICAL PORES

Influence of Cell Wall Material and Cell Numbers on Mechanical Properties of Closed-Cell Aluminum Foams

Research and Revise on Constitutive Equation of 7050-T7451 Aluminum Alloy in High Strain Rate and High Temperature Condition

Experimental approach for characterizing the nonlinear, time and temperature‐dependent constitutive response of open‐cell polyurethane foams

Study on the Compression Properties and Deformation Failure Mechanism of Open‐Cell Copper Foam

Fabrication and Compressive Behavior of Open-Cell Aluminum Foams Via Infiltration Casting Using Spherical CaCl2 Space-Holders

Investigation of Density- and Strain Rate-dependent Strain Hardening-softening-coupled material Behavior of Polyurethane Foams using Elasto-viscoplastic Constitutive Model

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Early Compressive Deformation of Closed-Cell Aluminum Foam Based on a Three-Dimensional Realistic Structure

Mechanical Properties and Constitutive Model of Aluminum Powder/rubber Matrix Composites Compressed at Various Strain Rates

Numerical investigation of influences of porous density and strain-rate effect on dynamical responses of aluminum foam

Study on Constitutive Model of Cyclic Elastoplastic Behavior of 6082-T6 Aluminum Alloy

A new modelling method for open cell foam structure based on centroidal and capacity constraint power diagram