Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

Ray-thermal sequential coupled heat transfer analysis of porous media receiver for solar dish collector

Numerical Investigation on Porous Media Heat Transfer in A Solar Tower Receiver

Study on Heat Transfer and Stress Characteristics of the Pressurized Volumetric Receiver in Solar Power Tower System

Numerical Investigation on Uniformity of Heat Flux for Semi-Gray Surfaces Inside a Solar Cavity Receiver

An optimized model and test of the China’s first high temperature parabolic trough solar receiver

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Analysis on the Effects of Different Receiver Structures and Porous Parameters on the Volumetric Effects and Heat Transfer Performance of Porous Volumetric Solar Receiver

A theoretical heat transfer analysis of different indirectly-irradiated receiver designs for high-temperature concentrating solar power applications

Numerical investigation on heat transfer and thermoelastic stress in a solar cavity receiver

Numerical Study on Thermal Performance of a Solar Cavity Receiver with Different Depths

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Experiment and optimization study on the radial graded porous volumetric solar receiver matching non-uniform solar flux distribution

Design, Simulation and On-Sun Experiments of a Modified Sliding-Bed Particle Solar Receiver for Coupling with Tower Concentrating System

An experimental investigation on thermal and optical analysis of cylindrical and conical cavity copper tube receivers design for solar dish concentrator

Analysis of radiative effect under local thermal non-equilibrium conditions in porous media-application to a solar air receiver

Numerical Evaluation on the Thermal Performance of the Solar External Cylinder Receiver Using Monte Carlo Ray-Tracing Algorithm

GPU-based Monte Carlo Ray Tracing Simulation Considering Refraction for Central Receiver System

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO2 as heat transfer fluid

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

Solar-thermal conversion investigation using surface partition method for a cavity receiver with helical pipe

A new methodology of thermal performance improvement and numerical analysis of free-falling particle receiver