Abstract:An in-situ reaction controlled non-solvent induced phase separation (RC-NIPS) method was developed to tailor the morphology of polyvinyl chloride (PVC)/styrene-maleic anhydride (SMA) grafting polyethylene glycol (PEG) (SMA-g-PEG) blend ultrafiltration (UF) membrane. Herein, PVC and SMA was dissolved in dimethylacetamide (DMAc) solvent to prepare a casting solution (16 wt.% polymer concentration) at 50 °C. Subsequently, PEG (20 kDa) as an additive and reactant was added to the casting solution at a mass ratio of PEG to the polymer 1/1 wt./wt. to enhance the hydrophilicity and mechanical elongation of the membrane. Results demonstrated that the casting solution with PVC/SMA = 3/1 wt./wt. was an entirely compatible system. The viscosity of the casting solution with adding PEG gradually increased from 692 mPa s to1880 mPa s at the initial stage and 4780 mPa s at 42 h, then rose sharply to 27,320 mPa s at 84 h. This behavior was ascribed to the esterification reaction between PEG and SMA, leading to pre-gelation and gelation of the system. Whereafter, SMA-g-PEG graft polymers were obtained. Meanwhile, the degree of grafting (DG) increased from 0.40% at 12 h of the reaction to 2.61% at 42 h. Afterwards, a phase inversion using water as coagulation was used to prepare PVC/SMA-g-PEG blend membrane after a certain time of the esterification reaction. It was found that the morphology of resultant membranes systematically changed from asymmetric structure with a dense top layer and finger-like sublayer at the initial stage to a dense layer with a fully sponge-like structure after 18–42 h reaction. The PVC/SMA-g-PEG membrane obtained after the reaction of 42 h demonstrated better hydrophilicity, high pure water permeance and excellent toughness due to the internal plasticization of water molecules. The membrane also exhibited a high BSA rejection (>95%) and fouling recovery rate (FRR) (85.9%). Our work provides some insights on tailoring the UF membrane structure and simultaneously enhancing permeability, antifouling performance and toughness.

Morphological Control of Porous Ethylene-Vinyl Acetate Copolymer Membrane Obtained from a Co-Continuous Ethylene-Vinyl Acetate Copolymer/poly(ϵ-Caprolactone) Blend

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

MICROPOROUS PVDF-HFP-BASED POLYMER MEMBRANES FORMED FROM SUPERCRITICAL CO2 INDUCED PHASE SEPARATION *

Triblock copolymers of methyl methacrylate/N-vinyl pyrrolidone and their hydrophilication effects on poly(vinylidene fluoride) porous membranes

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Effect of the Casting Solvent on the Crystal Characteristics and Pervaporative Separation Performances of P(Vdf-Co-Hfp) Membranes

Controlling Pore Size and Wettability of A Unique Microheterogeneous Copolymer Film with Porous Structure

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect Of Fiber Structure On The Properties Of The Electrospun Hybrid Membranes Composed Of Poly(E-Caprolactone) And Gelatin

Encapsulation and controlled release of lysozyme from electrospun poly(epsilon-caprolactone)/poly(ethylene glycol) non-woven membranes by formation of lysozyme-oleate complexes.

Selective Permeation of CO2 Through a Composite Membrane with a Separation Layer of 2-N,n-dimethyl Aminoethyl Methacrylate and Acrylic Acid Copolymer

Preparation of EVOH hydrophilic microporous membrane by thermally induced phase separation

Constructing Microstructures of Chlorinated Polyvinyl Chloride Microporous Membranes by Non-solvent Induced Phase Separation for High Permeate Flux and Rejection Performance

Effect of formation conditions of poly(ethylene-co-vinyl acetate) membrane on the membrane physical structure and pervaporation properties in the recovery of ethyl acetate from aqueous solution

Tailoring the micro-structure of PVC/SMA-g-PEG blend ultrafiltration membrane with simultaneously enhanced hydrophilicity and toughness by in situ reaction-controlled phase inversion

Study on Preparation and Performance of Modified Polyvinyl Chloride-co-vinyl Acetate Microfiltration Membranes

Improving CO2 Permeation and Separation Performance of CO2-philic Polymer Membrane by Blending CO2 Absorbents

Effect of Posttreatment on Morphology and Properties of Poly(ethylene‐co‐vinyl Alcohol) Microporous Hollow Fiber Via Thermally Induced Phase Separation

Preparation and Properties of Elliptic Leaves Silica/polyvinyl Alcohol Pervaporation Composite Membranes

Flexible Bi-Continuous Mesostructured Inorganic/polymer Composite Membranes

Preparation of PVDF/PS Blend Micro- Porous Membrane