Abstract:Low Density Polyethylene (LDPE) is blended with High Density Polyethylene (HDPE) and three types of Polypropylene (PP) having different melting index (MI), respectively. The compatibility of LDPE/HDPE blends is characterized by using thermal analysis and rheology methods. Differential scanning calorimeter (DSC) traces and rheology methods confirmed their good compatibility. For LDPE/PP blends, the incompatibility has been widely acknowledged in the literature. The distribution of the PP phase in the blend is investigated using polarized optical microscopy (POM). It is found that the phase structure is closely related to the blend composition and the viscosity ratio of the blend components. Extrusion foaming of the blends is conducted using a single extruder fitted with a CO2 gas injection system. Under similar foaming conditions, the compatible LDPE/HDPE blends all generated a uniform cell morphology and achieved roughly the same expansion ratio. Although the incompatible interface is beneficial to cell nucleation, the LDPE/PP blends did not achieve satisfactory foaming performance. To determine the differences in the foaming behavior of the two blends, the viscoelastic properties and diffusion coefficients of supercritical CO2 in the blends, were accurately measured via rheology and magnetic suspension balance (MSB) methods. The results indicate that the viscoelastic properties did not show a dominant role in determining the foaming behavior, by contrast, CO2 diffusion is found to be the key factor affecting foaming performance especially in the case of a co-continuous phase structure. (C) 2016 Elsevier B.V. All rights reserved.

Size Distribution and Anisotropy of the Minor Phase Droplets in Polypropylene/Ethylene-Octene Copolymer Blends: Effects of Shear and Component Miscibility

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Fractionated Crystallization and Self-Nucleation Behavior of Poly(Ethylene Oxide) in Its Miscible Blends with Poly(3-Hydroxybutyrate)

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Analysis of phase morphology and dynamics of immiscible PP/PA1010 blends and its partial-miscible blends during melt mixing from SEM patterns

Development of Dispersed Phase Size and Its Dependence on Processing Parameters

Effect of composition distribution on miscibility and co-crystallization phenomena in the blends of low density polyethylene with conventional and metallocene-based ethylene–butene copolymers

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Morphology Development in Multi-Component Polymer Blends: I Composition Effect on Phase Morphology in PP/PET Polymer Blends

Injection molding and shear‐induced stress simulation of poly (styrene‐ethylene‐butylene‐styrene) and polypropylene blends

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Miscibility of isotactic polypropylene with random and block ethylene-octene copolymers studied by atomic force microscopy-infrared

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers

Epitaxial Crystallization and Oriented Structure of Linear Low-Density Polyethylene/Isotactic Polypropylene Blends Obtained Via Dynamic Packing Injection Molding

Effect of Phase Compatibility on the Foaming Behavior of Ldpe/Hdpe and Ldpe/Pp Blends with Subcritical Co2 As the Blowing Agent

Closely Packed Conductive Droplets with Polygon-Like Patterns Confined at the Interface in Ternary Polymer Blends

Microstructures and Mechanical Properties of Polypropylene/polyamide 6/Polyethelene-Octene Elastomer Blends

Effect of Phase Morphology on the Reactive Blending

Experimental Studies on the Phase Separation Behavior of Molten Benzenesulfonate-Modified PET/PA6 Blends

Morphology and Dynamic Mechanical Properties of High Density Polyethylene/petroleum Resin/polyethylene–octylene Elastomer Blends