Abstract:Ultrahigh molecular weight polyethylene (UHMWPE) fibers have been investigated for years to improve performance with gel spinning process for wide applications in industry. Various spin solvents have been attempted including paraffin oil, decahydronaphthalene (decalin), kerosene etc. However, more work still needs to be done because of environmental issues or long extraction process of the aforementioned solvents. Recently, polybutene was found to be an effective spin solvent for UHMWPE fibers, which is environmentally friendly and widely available on the market. Besides producing high strength fibers, compared to paraffin oil, polybutene can form a gel with UHMWPE showing stronger phase separation behavior at room temperature. Because of this property, more extraction solvents can be saved. It was also demonstrated with experiments that the extraction efficiency is higher than that of the gel fiber formed with paraffin oil. Thus, polybutene has high potential to be used in large-scale production of UHMWPE fibers, which deserves further study. In this work, polybutene with different molecular weight was used to form spin dopes with UHMWPE. The dope concentration for each type of polybutene was also varied to check the effect of molecular weight and dope concentration on fiber properties. Viscoelastic properties of the spin dopes were obtained with parallel plate rheometry while thermodynamic properties of the dopes were characterized with differential scanning calorimetry (DSC) and thermal gravitational analysis (TGA). With optimized processing conditions, high strength fibers were collected and the crystalline structure was examined with wide angel X-ray diffraction (WAXD). DSC and TGA data also provided support for the effect of molecular weight and concentration of polybutene. It can be found that stronger fibers are obtained with lower concentration spin dopes. The viscosity of the dopes and corresponding spinning conditions are significantly affected by molecular weight of polybutene. Extraction efficiency is affected by both molecular weight and dope concentration. To obtain cost-effective superstrong UHMWPE fibers, an optimized design is needed based on the molecular weight of polybutene and the spin dope concentration.

Gelation/crystallization Mechanisms of UHMWPE Solutions and Structures of Ultradrawn Gel Films

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Preparation of Microporous Ultra High Molecular Weight Polyethylene (uhmwpe) by Thermally Induced Phase Separation of A Uhmwpe/Liquid Paraffin Mixture

Investigation of the Extraction Process in Gel‐spinning Technology for Ultrahigh‐molecular‐weight Polyethylene Fibers by Low‐field Nuclear Magnetic Resonance

Studies of UHMWPE gel crystallizing films by small-angle X-ray diffraction

Rheological Properties of UHMWPE/HDPE Blend Gels and Morphology and Mechanical Properties of Gel‐spun Fibers

Ultra-drawing of low molecular weight polyethylene — ultra-high molecular weight polyethylene blend films prepared by gelation/crystallization from semi-dilute solutions

Dissolving of Ultra-high Molecular Weight Polyethylene Assisted Through Supercritical Carbon Dioxide to Enhance the Mechanical Properties of Fibers

Hot-Drawing of Ultrahigh-Molecular-Weight Polyethylene Gel Films

Enhancing Gel Spinning of Ultra-High Molecular Weight Polyethylene: Insights into Rheology and Microstructure

Effect of Molecular Weight and Concentration on Gel-Spun UHMWPE Fibers with Polybutene As a New Spin Solvent

Morphology and mechanical properties of low‐molecular ‐ weight polyethylene and ultrahigh‐molecular‐weight polyethylene films drawn up to 200‐fold

Thermal Analysis of PE Extended Chain Crystal of PE Extended Chain Crystal from Gel Spinning

Heterogeneous Distribution of Entanglements in a Nonequilibrium Polymer Melt of UHMWPE: Influence on Crystallization Without and with Graphene Oxide

Extended Chain Crystals of Ultra High Molecular Weight Polyethylene Fiber Prepared by Melt Spinning

The effect of concentration distribution of Gauche conformation on ultra-drawing of ultrahigh molecular weight polyethylene gel-films prepared from solution

Structure and Properties of Gel‐spun Ultra‐high Molecular Weight Polyethylene Fibers Obtained from Industrial Production Line

Characteristics Of Ultradrawn Blend Films Of Ethylene-Methyl Methacrylate Copolymer And Ultrahigh Molecular Weight Polyethylene Prepared By Gelation/Crystallization From Solutions Estimated By X-Ray, Positron Annihilation, And C-13 Nmr

Structural evolution of ultra-high molecular weight polyethylene gel film stretching at different temperatures with reservation of shish crystals

Two‐stage Drawing Process to Prepare High‐strength and Porous Ultrahigh‐molecular‐weight Polyethylene Fibers: Cold Drawing and Hot Drawing

Study on Structures and Properties of Ultra-Hot Drawing UHMWPE Fibers Fabricated Via Dry Spinning Method