Abstract:Nano composites have been utilized increasingly because of their high strength, stiffness, toughness, and through-thickness properties. The incorporation of carbon nano fibers with a high aspect ratio and extremely large surface area into glass/epoxy polymer composites improve their tensile and compression properties significantly. Although a number of efforts have been made to improve various properties by mixing nano particles directly into resin, however, it could lead to high viscosities which create problems during processing. In this particular study, an attempt has been made to investigate tensile and compression behavior of nano composites by using, state of the art, a different technique i.e spraying the Carbon Nano Fibers (CNF) on dry woven glass pre-form before infusion. The nano composite samples were prepared using a spraying methodology i.e dispersing the 2.0 weight percent CNF solution on glass fabric, and evaporating the solvent such that only nano fibers remain on perform, followed by Vacuum Assisted Resin Transfer Molding (VARTM). Tensile and compression tests were performed to evaluate the effectiveness and behavior of CNF addition on these mechanical properties. Results indicated simultaneous improvement in tensile and compression properties by incorporating a very small amount of carbon nano fibers into the matrix system. 18-21 percent improvement in tensile strength and 6-9 percent in compressive strength, with respect to the neat composite. The rise in their modulus has also been discussed in detail and part of this study. For in-depth analysis, microscopic approaches were also carried out to investigate the fracture behavior and mechanism of material. Scanning electron microscopy of fractured surfaces revealed improved primary fiber matrix adhesion and indications of CNF-induced matrix toughening due to the presence of CNFs. SEM evaluation also revealed relatively less damage in the tested fracture surfaces of the nano phased composites in terms of matrix failure, fiber breakage, matrix fiber de-bonding, and de-lamination, compared to the neat system.

Nano-analysis on the structure and chemical composition of the interphase region in carbon fiber composite

Nano-analysis on the Structure and Chemical Composition of the Interphase Region in Carbon Fiber Composite Part A Applied Science and Manufacturing

Characterization of the Interphase in Carbon Fiber/Polymer Composites Using A Nanoscale Dynamic Mechanical Imaging Technique

Enhanced Interfacial Properties of High-Modulus Carbon Fiber Composites Via Molecular Assembly on Fiber Surface

Surface Characteristics of Different Cross-Section Carbon Fibers and Its Effect on Interfacial Adhesion Properties of Composite

Investigation the interphase formation process of carbon fiber/epoxy composites using a multiscale simulation method

Investigation of the nanostructure and nanomechanical properties of the interphase in carbon fiber reinforced polyamide-6 composite

ATOM FORCE MICROSCOPE STUDY ON INTERPHASE CHARACTER OF CARBON FIBER/POLYARYLACETYLENE COMPOSITES

Interface Probing by Dielectric Frequency Dispersion in Carbon Nanocomposites

PREPARATION AND MECHANICAL PROPERTIES OF CARBON NANOTUBES/RESIN EPOXY COMPOSITE

Research on Structure and Performance of Different Micro-zone in Carbon/Carbon Composites

Micro- and nano-structural investigations of C/C composites

Interphase formation and fiber matrix adhesion in carbon fiber reinforced epoxy resin: influence of carbon fiber surface chemistry

Quantitative Analysis Based on Atomic Force Microscopy Characterization of Interfacial Properties Between Carbon Fibers and Epoxy Resin Subjected to Hygrothermal and Thermal Treatments

Probing the Nanostructure and Reactivity of Epoxy-Amine Interphases

Molecular Simulation of the Interfacial Properties of an Epoxy Composite Reinforced Using a Carbon Nanotube/Carbon Fiber Hybrid

Preparation, Characterization, and Modeling of Carbon Nanofiber/epoxy Nanocomposites

Functional Interphases with Multi-Walled Carbon Nanotubes in Glass Fibre/epoxy Composites

Characterization of the interface and interphase region in the multi-walled carbon nanotube modified epoxy resin/carbon fiber hybrid nanocomposite

Tensile and compression behavior of woven glass/epoxy nano composites based on spraying methodology

Molecular structure effects of mesophase pitch and isotropic pitch on morphology and properties of carbon nanofibers by electrospinning