Abstract:Herein, as a binder (or catalyst ionomer) for AEMFCs, we investigated the effect of two different cationic copolymers based on poly(phenylene oxide) (PPO) with N-cyclic quaternary ammonium (QA) groups, including six-membered dimethyl piperidinium (DMP) and bis-six-membered azonia-spiro undecane (ASU). An earlier report on the same polymers for membranes in AEMFCs indicated the better electrochemical performance of PPO-ASU compared with PPO-DMP. Therefore, we would like to investigate these two polymers for catalyst ionomers. The outcome in this study using these two copolymers as catalyst ionomers indicates the opposite result; the electrochemical performance of the PPO-DMP ionomer is much better than the PPO-ASU ionomer. The commercial Fumion ionomer was used for the qualitative comparison. The density functional theory (DFT) calculation of the adsorption energy according to different orientations of the cationic groups on the catalyst surface shows that there is no difference between the adsorption energy of DMP and ASU cations, in compliance with the orientations of the cations. Although the PPO-ASU ionomer membrane has the highest hydroxide conductivity at 60 degrees C in liquid water, the hydrogen oxidation/reduction (HOR) activity of PPO-DMP and PPO-ASU showed similar values with the Fumion ionomer. While the PPO-DMP ionomer membrane shows relatively large fuel gas (hydrogen) permeability in dry and wet conditions, due to the chain flexibility and the presence of two methyl groups compared to the single methyl groups and lower flexibility of the PPO-ASU and Fumion ionomers. The electrochemical performance of a membrane electrode assembly (MEA) using the PPODMP ionomer exhibited an exceptional peak power density of 335 mW cm(-2) compared to lower peak power densities the of PPO-ASU and Fumion ionomers under 60 degrees C and a fully humidified condition (H-2/O-2). The SEM images of MEAs after testing supports the conclusion that the PPO-DMP ionomer forms a uniform catalyst interface that is very well bound between the electrode and membrane, unlike the PPO-ASU and Fumion ionomers. The PPO-DMP ionomer membrane also showed better tensile strength and elongation at break than the PPO-ASU ionomer membrane. Therefore, we conclude that the well-prepared three-phase boundary structure played a critical role for the catalyst ionomer in each electrode, overcoming one of the critical performancelimiting factors.

Impact of cation selection on proton exchange membrane fuel cell performance with trimethylethyl amide, ethylpyridinium and ethylmethyl imidazolium ionic liquid carried by poly(vinylidene fluoride) membrane as electrolyte

Polybenzimidazole/ionic-liquid-functional Silica Composite Membranes with Improved Proton Conductivity for High Temperature Proton Exchange Membrane Fuel Cells

Novel Cross-Linked Membranes Based on Polybenzimidazole and Polymeric Ionic Liquid with Improved Proton Conductivity for HT-PEMFC Applications

Impact of a protic dimeric ionic liquid on PEM fuel cell performance and durability

Enhancing Polymer Electrolyte Membrane Fuel Cells with Ionic Liquids: A Review

Imidazolium-Quaternized Poly(2,6-Dimethyl-1,4-Phenylene Oxide)/Zeolitic Imidazole Framework-8 Composite Membrane as Polymer Electrolyte for Fuel-Cell Application

Effect of <i>N</i>-cyclic cationic groups in poly(phenylene oxide)-based catalyst ionomer membranes for anion exchange membrane fuel cells

Proton Exchange Membrane Fuel Cell Working At Elevated Temperature With Ionic Liquid As Electrolyte

A Review on Ionic Liquids-Based Membranes for Middle and High Temperature Polymer Electrolyte Membrane Fuel Cells (PEM FCs)

Bipyridine polybenzimidazole ionomer with optimized electrochemical boundaries enhanced power density of high-temperature proton exchange membrane fuel cells by 2.5 times

Development of imidazolium-type alkaline anion exchange membranes for fuel cell application

Phosphonated Ionomers of Intrinsic Microporosity with Partially Ordered Structure for High-Temperature Proton Exchange Membrane Fuel Cells

Ionic Liquid in Phosphoric Acid-Doped Polybenzimidazole (PA-PBI) as Electrolyte Membranes for PEM Fuel Cells: A Review

Decisive Effect of Hydrophobic Rigid-Flexible Coupled Side Chains of Polycarbazoles on the Performance of Anion Exchange Membranes for Fuel Cells

A Critical Review on the Use of Ionic Liquids in Proton Exchange Membrane Fuel Cells

Long side-chain N -heterocyclic cation based ionic liquid grafted poly(terphenyl piperidinium) membranes for anion exchange membrane fuel cell applications

Poly (ether ether ketone ketone) based imidazolium as anion exchange membranes for alkaline fuel cells

Alkaline polymer electrolytes containing pendant dimethylimidazolium groups for alkaline membrane fuel cells

Novel chitosan-ionic liquid immobilized membranes for PEM fuel cells operating above the boiling point of water

Development of proton-exchange membrane fuel cell with ionic liquid technology

Structural and Transport Properties of Hydrophilic and Hydrophobic Modified Ionomers in Proton Exchange Membrane Fuel Cells