Abstract:Liquid Sb has been accepted for direct carbon solid oxide fuel cell anode material for its unique physical and chemical properties. Sb and Sb2O3 have a relatively low melting point of 630 and 636 °C respectively and the electrochemical formed Sb2O3 would drift away from the Sb/electrolyte interface because of density difference. So the density difference and viscosity of the liquid phases have influence on the two phase convection and the average thickness of insulator Sb2O3 layer. Sb1-x -Ag x (x = 0.1, 0.2, 0.3) alloy has a lower melting point and higher density than pure Sb. Since Ag2O would not exist stably at temperature higher than 300 °C, Ag atoms in the Sb1-x Ag x anode will not participate to the electrochemical reaction with O2- at intermediate temperature. A tubular 8 mol.% Y2O3 stabilized ZrO2 (YSZ) supported SOFC with La0.6Sr0.4Co0.2Fe0.8O3-Gd0.1Ce0.9O2-δ (LSCF-10GDC) as the cathode and Sb1-x -Ag x as anode was fabricated by slurry-casting, slurry-dipping and sintering processes. The primary I-V/I-P performance of the Sb1-x -Ag x abode cells was much lower than the Sb anode cell. Alloying Ag seemed to have a negative influence on the electrochemical reaction between Sb and O2-, which might due to Ag atoms taking partial Sb atoms positions. Working at a current density from 0.1, 0.2, 0.3, 0.4 to 0.5 A cm-2 at 750 °C, the final I-V/I-P performance of the alloy anodes cells was just a little lower than the Sb anode cell. The EDX analysis and SEM pictures of the tested cells revealed that elements re-distribution happened in the anode. The primary uniform distributed Sb1-x -Ag x alloy appeared to be a layered structure and the Ag content in the button layer was higher than that in the upper layer. Figure 1

Polarization Characteristics of Liquid Antimony Anode with Smooth Single-Crystal Solid Oxide Electrolyte

Numerical Simulation and Experimental Characterization of the Performance Evolution of A Liquid Antimony Anode Fuel Cell

Effects of Interface Roughness on A Liquid-Sb-Anode Solid Oxide Fuel Cell

Performance Characteristics of Liquid Antimony Anode Direct Carbon Fuel Cell

Polarization Behavior of High Temperature Solid Oxide Electrolysis Cells (SOEC)

Hot Corrosion of Yttria-Stabilized Zirconia by Liquid Antimony and Antimony Oxide

Liquid Antimony-Silver Alloys As Anodes for Direct Carbon Solid Oxide Fuel Cells

Plasma-spray Derived, Corrosion-Resistive Electrolyte for Liquid Antimony Anode Direct Carbon Fuel Cell

Sb-Ag Liquid Alloy Anode for Solid Oxide Fuel Cell with Carbon As Fuel

Performance Enhancement of Liquid Antimony Anode Fuel Cell by In-Situ Electrochemical Assisted Oxidation Process

Optimization of strontium molybdate based composite anode for solid oxide fuel cells

Development of Liquid Antimony Anode-Based Fuel Cells: Effects of Reaction-Induced Convection on Mass Transfer and Electrochemical Performance

Composition optimization of samarium strontium manganite-yttria stabilized zirconia cathode for high performance intermediate temperature solid oxide fuel cells

Ni–Sm0.2Ce0.8O1.9 Anode-Supported YSZ Electrolyte Film and Its Application in Solid Oxide Fuel Cells

Sulfur Poisoning and Attempt of Oxidative Regeneration of La0.75Sr0.25Cr0.5Mn0.5O3−δ Anode for Solid Oxide Fuel Cell

Hot Corrosion of Gd2O3-doped CeO2 Electrolyte in Solid Oxide Fuel Cells with a Liquid Antimony Anode

Co-synthesized Y-stabilized Bi2O3 and Sr-substituted LaMnO3 Composite Anode for High Performance Solid Oxide Electrolysis Cell

Sm0.2Ce0.8O1.9/Y0.25Bi0.75O1.5 Bilayered Electrolytes for Low-Temperature SOFCs with Ag-Y0.25Bi0.75O1.5 Composite Cathodes

Liquid Antimony Anode Fluidization Within A Tubular Direct Carbon Fuel Cell

Introducing Anode Fluidization into a Tubular Liquid Antimony Anode Direct Carbon Fuel Cell

Intermediate-temperature solid oxide fuel cells with Y 0.25Bi0.75O1.5-Ag cathodes